Availability
Vortech supercharger systems for GM LS-Swaps operate at an even higher level of sophistication than any original equipment system. They're currently one of the most popular engine swap power plants in the world. In every application, the LS systems have established themselves to be fantastic platforms to swap into just about anything. They operate at an even higher level of sophistication, with a boost curve generated by Vortech's superchargers that are ideally matched with today's highly evolved engines and give you power when you need it. The supercharger and the technologically advanced subsystems fully integrate into the vehicle's existing platform, yielding a smooth continuity of power and performance.
( 3 )
$3,915.99
Whether you have a mundane daily driver or a high-horsepower racer, Vortech has a supercharger kit for you. Receive unprecedented value and add up to 75 percent more horsepower to your small block Chevy with these carbureted entry-level supercharger kits. These kits feature the Vortech PowerHat with diffusion technology and they will produce approximately 5 psi at 5,500 rpm on a mildly modified 350 engine. Additionally, most OEM Saginaw-type power steering pumps can be attached to the Vortech mounting bracket by using the supplied hardware in the kits. Smash that pedal and step into the world of superchargers! Vortech carbureted entry-level supercharger kits have you covered. Important information or requirements for the Vortech carbureted entry-level supercharger kits: * These systems were designed to fit on engines equipped with a "long" water pump and OEM V-belt drives or serpentine accessory drives; for correct belt alignment, the proper accessory drive crank pulley and accessory bracketry must be used * Earlier models equipped with short water pumps will require a long water pump to be installed * Quick Fuel, Demon, or Holley 4150-type, 4-barrel carburetor with mechanical secondaries designed for "blow-though" applications (may require rejetting or minor modification) * High performance, boost-referenced fuel pump * Compressor bypass valve * Accessory belts (will vary per application, depending on accessory configuration and supercharger pulley diameters) * Minor (bottom-side) modifications may be required, depending on the vehicle and type of intake manifold installed on the engine
( 5 )
$3,364.99
Whether you have a mundane daily driver or a high-horsepower racer, Vortech has a supercharger kit for you. Their centrifugal supercharger kits feature lightweight aluminum impellers that are heat-treated and high-speed balanced to ensure smooth operation. An O-ring compressor housing seal and an innovative impeller seal improve sealing and reduce friction. Vortech has taken away the headaches of building a custom kit by engineering these kits to have a true OEM-quality fit and finish. Each kit is 100 percent complete, right down to the wire ties. Most kits include a matched compressor supercharger unit with SQ technology for "Super Quiet" operation. A high-flow air intake system with a reusable air filter, heat-resistant silicone hose couplings, and premium-grade flex hose is included as well. Additional features: * Flow-tested cast aluminum and/or urethane air discharge tubing * OEM-style, heat-treated cast 356 aluminum mounting brackets * Supercharger drive pulley * Integrated belt tensioner * Premium drive belt * Stainless steel clamps * Heavy-duty mounting hardware * Choice of satin or polished finish * Step-by-step, fully illustrated installation manual
( 9 )
$3,633.99
—
$10,390.99
If you are looking for a top-quality racing bypass valve, look no further than these Maxflow valves from Vortech. Key features include: * 320 cfm flow at 8 psi * Gasket for installation * Compact design is ideal for import applications and tight engine compartments * 2-bolt mounting pattern will retrofit to standard HKS/Greddy-style mounting pads
( 14 )
$394.99
—
$423.99
Vortech crankshaft pulleys are made of 6061 T-6 aluminum that's hard anodized and built to SAE standards. They are CNC-machined for maximum surface contact and feature an improved belt traction profile.
( 11 )
$133.99
—
$454.99
Vortech supercharger pulleys are made of 6061 T-6 aluminum, hard anodized, and built to SAE standards. They are CNC-machined for maximum surface contact and are available in several styles to suit your application needs.
( 42 )
$112.99
—
$202.99
Vortech supercharger systems designed to increase horsepower and torque contain many high-performance components. Dipstick assemblies are one of these quality parts and are available in various degrees of tilt.
( 2 )
$72.99
Vortech Engineering standard bypass valves are specifically designed for street applications. They help eliminate compressor surge and reduce heat soak in the discharge tube. These units are recommended for vehicles running 6 to 12 psig. Both the inlet and outlet mate to a 1 in. hose.
( 4 )
$112.99
All Vortech V3 superchargers are shipped with temporary vent plugs in the ventilated gear case assembly. These are permanent replacement plugs to install after removing the shipping fittings. Without the proper vented plugs in place, you will blow the seals out of your supercharger. A ventilated gear case assembly eliminates any potential internal pressure issues that are currently associated with non-vented competitive designs. Vortech parts will keep your supercharger at optimum performance levels.
( 2 )
$43.99
Vortech PowerHats are cast aluminum carburetor hat assemblies designed to work on "blow-though" applications with Quickfuel, Demon, or Holley 4150-type 4-barrel carburetors with mechanical secondaries. PowerHats feature diffusion technology for easier tuning and maximum power output, plus they have a unique low profile that permits near-360 degree rotation for universal fitment. They're available with single or dual ports in polished or satin finishes. Put a new lid on your carburetor with Vortech PowerHat carburetor hat assemblies.
Not Yet Reviewed
$493.99
—
$561.99
These Vortech replacement idler pulley assemblies are designed to fit your Vortec supercharger without any modifications. They feature a durable bracket and idler pulley that can handle the big boost of today's superchargers. Available for all Vortec supercharger kits, the Vortech replacement idler pulley assemblies will make sure that you don't throw any belts off during higher rpm conditions.
( 2 )
$73.99
—
$202.99
Feed your supercharger with Vortech oil feed assemblies. Designed for a perfect fit in several applications, these assemblies include an oil feed hose, crimp ferrules, and the necessary fittings to do the job. And Vortech's red hose and brass fittings look great under the hood.
( 10 )
$69.99
—
$129.99
If you find that you need to replace the pulley bolts for your Vortech supercharger, these bolts will meet your needs. Designed to be direct replacements, they're made of high-quality materials and are available in a variety of sizes.
( 8 )
$20.99
The right brackets for the right performance--Vortech accessory tensioner mounting brackets. Belt tensioners are an important component in the operation of your supercharger drive system. And, bent or misaligned mounting brackets may be the culprits for abnormal belt tracking on your tensioner pulley. Get the proper fit and function, plus avoid problems and poor performance with Vortech accessory tensioner mounting brackets.
( 5 )
$80.99
—
$99.99
Vortech supercharger oil feed fittings will mount into the supercharger head unit and allow the oil to enter the case. They are manufactured from high-quality brass material and are designed to fit all Vortech centrifugal-style superchargers.
( 7 )
$91.99
Vortech Maxflow race bypass valve adapters are required to mount your Vortec Maxflow bypass valve. They are available in steel or aluminum for a variety of mounting styles. Welding and modification are required for installation.
( 1 )
$41.99
Vortech supercharger discharge tubes are designed to connect the supercharger head unit to the OEM throttle body. They are manufactured from high-quality aluminum and are available in satin or polished finishes. Complete the installation of your Vortech supercharger with Vortech discharge tubes.
( 4 )
$207.99
Save time and money with one of these mounting hardware kits, complete with flat head style screws, spacers, washers, and clips. Vortech mounting kits come with all necessary hardware for the installation of any style of rear valance for specified Mustangs. Vortech mounting hardware kits for 5.0L Mustangs do not include the mounting plate.
( 3 )
$78.99
Change the oil in your supercharger the easy way with one of these Vortech supercharger oil drain assemblies. They include an adapter to thread into your supercharger drain port and a section of rubber hose to give you more clearance from the engine and avoid getting oil on other engine components.
Not Yet Reviewed
$69.99
Vortech supercharger systems are designed to increase horsepower and torque, thanks to their many high performance components. These air inlet ducts, for instance, provide clean and unrestricted airflow to the engine—and lowering charge air temperatures will substantially improve both performance and engine longevity. The inlet duct connections utilize heat-resistant silicon sleeves and premium-quality stainless steel clamps to keep your system running at peak efficiency.
( 1 )
$103.99
—
$283.99
Vortech race bypass/blow-off valves flow 320 cfm at 8 psig, and feature a compact design that's ideal for imports and other vehicles with tight engine compartments. These units will retrofit to standard HKS/Greddy style mounting pads and outperform anything their size. An installation gasket is included, and steel or aluminum mounting flanges are available. The outlet mates to a 1.75 in. hose. Vortech race bypass/blow-off valves are offered in several finishes.
( 2 )
$394.99
These high performance air filters by Vortech are constructed from high-flow aluminum mesh and cotton fiber that help to direct and straighten the air for improved flow and circulation. These filters use misted oil to trap even the smallest particles.
( 9 )
$54.99
—
$108.99
These Vortech Maxflow BV57 bypass valves flow 1,300 cfm at 10 psi boost. They feature a large rolling diaphragm configuration with a 4 AN signal hose connection and dual filtered vents that allow for quick valve response. The valve head attachment method provides valve articulation for perfect sealing to the mechanically retained valve seal. The Vortech Maxflow BV57 bypass valves also feature adjustable spring preload and reconfigurable signal input locations. They can be mounted in any position and are adaptable to all types of boosted engine installations. They are designed for use in speed density configured applications only.
Not Yet Reviewed
$613.99
Vortech pulley spacers are the prefect-fit for your supercharger system. They are crafted from aluminum and hardcoated black. Replace with what you know will fit and perform to expectations; choose Vortech pulley spacers from Vortech.
Not Yet Reviewed
$24.99
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
