Availability
This MSD 2-Step launch controller connects right to your late model Ford to produce consistent launches and quicker 60-foot times by setting an rpm limit to stage with. When activated, the rpm will be held at a steady rpm and once the green light comes on, release the clutch and take off. The rpm is adjusted with two built-in rotary dials ranging from 1,800-9,900 rpm in 100 rpm increments. A handy LED shows when the launch rev limit is active.
( 8 )
$315.95
If your Coyote-powered Ford was built after February 23, 2016, and you need a 2-Step rev-limiter for consistent burnouts or launches, MSD part number 87311 has you covered. When activated, the 2-Step will hold your engine at a constant RPM. This can be achieved by way of a clutch switch or push button. As soon as your activation switch or button is released, full ignition is restored and you're off to the races. The RPM is adjusted with two built-in rotary dials ranging from 1,800-9,900 rpm in 100 rpm increments. A handy LED shows when the launch rev limit is active.
Not Yet Reviewed
$376.95
These MSD Launch Masters connect right to your late model Ford to produce consistent launches and quicker 60 ft. times by setting an rpm limit to stage with. When the MSD Launch Masters are activated, the rpm will be held steady. Once the green light comes on, release the clutch and take off, but be sure to hold on! The Launch Masters' rpm is adjusted with two built-in rotary dials ranging from 1,000-10,900 rpm in 1,000-rpm and 100-rpm increments. A handy LED shows when the launch rev limit is active.
( 11 )
$349.95
MSD Power Grid wide band oxygen sensor modules provide valuable air/fuel ratio data to your MSD Power Grid, data logger, or air/fuel ratio gauge. These modules feature: * Plug-and-play with MSD Power Grid * Easy set-up; no free-air calibration required * Completely sealed unit for durability in race environments * Bosch 4.9 oxygen sensor * 0 to 5 V output to run an air/fuel gauge or data logger * Dual-color LED provides on board diagnostics * Multiple modules can be used on a single Power Grid * Data logs air/fuel ratio and heater voltage * Fuel calibration options for gasoline, methanol, ethanol, E85, propane, and diesel * Custom fuel calibration option can be programmed by user
( 2 )
$334.95
On Sale
Hoop up your Atomic TCU with MSD Atomic transmission control module harnesses. They are designed to fit your specific transmission model and have the proper wiring connector for a direct fit.
( 7 )
$274.95
—
$299.95
MSD Atomic TBI throttle position sensor modules are designed for use with the MSD Atomic throttle body fuel injection system. They connect inline to the Atomic TBI communication network and provide a common 0-5 V throttle position output signal required for the operation of an electronic overdrive transmission or other accessory.
( 3 )
$299.95
On Sale
Get on the performance grid with MSD Ignition Power Grid power modules. When connected to the Power Grid, they will data log all the functions--including time from launch and time or rpm of activation and deactivation. These timing controllers feature four high-current, solid-state switches that can be configured independently or in conjunction by time, rpm, and temperature switching on/off, as well as by percentage for nitrous systems. Each channel is capable of handling 20 amps of current without the use of a relay and can be used to activate fan, fuel pump, nitrous oxide system, throttle stop, and more--the possibilities are endless.
( 1 )
$749.95
$412.95
MSD Atomic transmission control modules are designed to adjust the operating parameters of later model electronically controlled 4-speed automatic overdrive transmissions. They're simple to configure with the supplied hand-held monitor--no PC required. You now have access to adjust shift points, adjust torque converter clutch behavior, select different levels of shift firmness, select between auto-shift and manual shift mode, and activate dyno mode to deliver repeatable chassis dyno results. The included hand-held monitor connects to them and can be left in place as a dashboard to monitor the transmission in real time, or can be disconnected when the configuration is complete. Once installed, these modules need only a few basic parameters to complete the initial setup. First, select the type of transmission you are using--all supported transmission types are listed in the menu. Other required fields include the number of engine cylinders, rear-end gear ratio, and tire height. Once this has been completed, you can now start and drive the vehicle, while taking advantage of the advanced setup menu items to dial-in the transmission to your liking. You can feel the results in real-time as a passenger manipulates the parameters and monitors the real-time data. Data available for viewing includes engine speed, vehicle speed, throttle position, transmission fluid temperature, shifter position, and commanded gear. Best of all, the MSD Atomic transmission control modules are available as completely stand-alone units or Brainwave-compatible for the Atomic EFI systems. A transmission controller harness is sold separately.
( 19 )
$349.95
MSD Ultimate HEI kits have everything you need to turn your early model GM HEI distributor into a great performance distributor. The MSD HEI modules feature special circuitry to produce 50 percent higher coil drive currents than stock modules, resulting in higher spark energy at racing rpm. By matching the coil specifications with the modules, MSD delivers more accurate timing and dwell control. The kits also include a high-quality rotor, a durable cap with brass terminals, and even a new dust cover.
( 19 )
$399.95
Communication is important. MSD Atomic EFI TBI handheld monitors are the devices you use to interface with your Atomic throttle body fuel injection (TBI) system. You'll be in the know about everything happening with your engine, from exact air/fuel ratio readouts to engine coolant temperatures. Not a software engineer? You don't have to be! True to MSD form, these handheld monitors are very easy to use. In the initial setup, you'll provide info that you already know--such as cubic inches, number of cylinders, and your desired rev limit. After that, you simply use the engine feedback as you would a dashboard gauge. Plus, the data gathered doesn't just disappear. The monitors display alerts and save them for up to 10 starts for you to review. Little device, big communication--MSD Atomic EFI TBI handheld monitors keep an eye on your engine's performance.
( 3 )
$429.95
MSD Power Grid wide band oxygen sensors are replacements for the MSD Power Grid wideband O2 sensor module. The LSU 4.9 is the robust design combined with a high production quality standard. They will also work with Holley Sniper EFI and Terminator X Systems. MSD Power Grid wide band oxygen sensors feature anti-seize pre-applied to sensor threads for an easy install and removal, and they are compatible with gasoline, methanol, ethanol, E85, propane, and diesel.
( 1 )
$299.95
MSD is excited to announce the next generation of 6-Series ignition controls--the 6AL-2! These all-new ignition controls combine a new housing, new digital controls, and more power in a sleek package. You still receive the 20 degree duration of multiple sparks, combined with higher output to ensure complete combustion. There is a 2-Step rev control built into the housing, but there are no rpm modules! Adjustments are made via four rotary dials for 100 rpm increment control! The all-new capacitive discharge ignition will easily connect to nearly any 12 V negative ground distributor system, even Hall-effect pickups. They offer higher output, with up to 135mJ and 535 V, and accept points and mag pickup triggers.
( 95 )
$449.95
These MSD 6TN and 6ALN ignitions are the ultimate choices for superior performance in harsh racing conditions. With sturdy vibration mounts and CD circuits encased in a clear 2-part silicone elastomer, they are virtually vibration-proof. A specially designed, weathertight, 6-pin connector meets NASCAR's 20-6.1 ignition wiring rule and provides a tight, positive-locking connection with individual seals to keep dirt and moisture from each connection. The 6TNs are equipped with a special 4-pin connector that plugs directly into an MSD soft touch rev control, while the 6ALNs have a built-in rev control. These rev controls are adjustable with plug-in modules and will save your engine from overrev damage caused by missed shifts or driveline failures. They'll work with virtually any 4, 6 (even-fire V6 only), or 8-cylinder engines.
( 6 )
$522.95
MSD Street Fire EFI distributors are ready to drop in your V8 engine and replace the worn-out OEM piece. They feature a factory-style ignition module, along with a durable new cap and rotor. The distributors use a cast housing, making them more affordable, but are much stronger than standard OEM distributors. The MSD Street Fire EFI distributors are available for both Ford and Chevy EFI engines.
( 26 )
$381.95
—
$399.95
MSD Circle Track HEI distributors were designed with the demands of racing in mind. These "stock appearing" units are peaked and tuned to provide ultimate reliability and strength to run circles around the competition. The bulletproof ignition module fires a high-output coil in the cap, while a specially designed, QPQ-coated chromoly advance cam and weight set ride on TIG-welded weight plate pins and a TIG-welded distributor shaft. This combination provides brute strength and precision timing from idle to maximum rpm. At the bottom, a QPQ-coated steel gear will run lap after lap, race after race, victory after victory without fatigue.
( 2 )
$435.95
On Sale
MSD digital multi-retard timing controls provide four different stages of retard, along with an adjustable start retard feature--with no modules! These units use a high-speed RISC micro-controller to direct the timing functions. This controller can make extremely quick compensations to the timing, while maintaining accuracy to within 1 degree. These circuits are thoroughly de-bounced and isolated for protection against Electro Magnetic Interference (EMI). There is also an innovative magnetic pickup compensation circuit built-in to allow for rock-steady timing with a variety of different mag pickups. There are four separate retard stages that can be activated independently or together for a total sum of retards. Each stage is adjustable from 0-9 degrees, and a maximum of 20 degrees of retard can be pulled out. On top of these great features, there is also an optional start retard circuit that can be programmed to retard the timing 5, 10, 15, or 20 degrees during cranking. Digital multi-retard timing controls can be used on 4, 6, or 8-cylinder engines, and must be used with an MSD ignition control.
( 2 )
$499.95
$274.95
MSD Power Grid 3-stage delay timing controls are an add-on module for use with the MSD Power Grid system (sold separately). These controls let you activate up to three individual outputs based on time. The outputs can trigger a relay to activate nitrous, shifter, etc.; when the clutch/transbrake is released, the Power Grid will start the timers through the CANN connection. They'll also display live ignition timing! Thanks to the advanced data acquisition features of the MSD Power Grid, all of the settings and values you set with the 3-stage delay timer can be reviewed after each run to assist in tuning the program for the next run. Now that's timing control!
( 1 )
$368.95
MSD three-stage retard controls allow you to retard your ignition timing in three different stages. You can activate one retard for a nitrous stage, and another at top-end in high gear for more mph, and still have another module left over for dual-stage nitrous systems. When activated together, the retard amounts are cumulative, so you get the total of the three. For example, if you pull 2 degrees, then 4 degrees on the second stage, and another 2 degrees at top-end, the total retard is 8 degrees (2+4+2=8). In addition to the individual retard stages, the Three Stage retard controls have an optional start retard function that retards the timing 10 or 25 degrees while cranking the engine. This makes starting high-compression engines with locked-out timing, such as crank trigger systems, much easier. These units easily connect to your MSD Ignition and can be triggered from points, electronic ignitions, crank triggers, or magnetic pickup distributors. They're supplied with a 2, 3, and 4 degree module, and must be used with an MSD 6, SCI, 7, 8, or 10 Series ignition.
( 4 )
$499.95
There are two ways to limit your rpms. The rough way simply cuts off ignition spark, which can cause backfiring, extreme engine roughness, and possible engine damage. The gentle way is with these MSD Soft Touch rev controllers. They use sophisticated computer circuitry to drop spark one cylinder at a time, until your engine is at or below its maximum rpm. Those cylinders are then fired on the next cycle, to prevent them from loading up with fuel. The result is smooth rev limiting action without all the rough stuff. There are two versions of the Soft Touch rev controllers--one for MSD's 6T, 6TN, 6HVC ignitions, and one for OEM electronic and points ignitions. Both come with 6,000, 7,000, and 8,000 rpm plug-in modules, and can be used with other modules or MSD's RPM module selector.
( 15 )
$275.95
On Sale
MSD Pro-Billet Ready-to-Run distributors are the perfect upgrade for weak OE electronic distributors, outdated points distributors, and large HEIs or DuraSparks. All that's required is to install the distributor in the engine, and connect three wires and the coil! A maintenance-free magnetic pickup accurately triggers this ignition with increased output from the amplifier, easily outperforming stock ignitions. It will smooth out the engine's idle, improve starting, and perform at a much higher rpm. The housing is machined from billet 6061-T6 aluminum, using state-of-the-art CNC mills and lathes for a unit with no porosity or weak areas. For stability and endurance, an oversized steel shaft spins in a top-mounted sealed ball bearing, while an extra-long sintered bushing guides the shaft at the base of the housing. This shaft also receives a QPQ coating for low friction wear and resistance against corrosion from humidity and ozone buildup. The distributors feature MSD's adjustable mechanical advance, which allows you to custom-tailor an ignition curve to match your engine's needs. Most models are also available with a vacuum advance canister to help improve economy. Order the model recommended for your vehicle and engine application.
( 327 )
$649.95
$357.95
—
$499.95
MSD Pro-Billet Ready-to-Run EFI distributors are the perfect upgrade when you start making serious power with your EFI Ford or Chevy. They use a stock-style trigger pickup and come with plug-in connectors. Installation is simple by removing the stock distributor, then plugging in and bolting the new one in place! A maintenance-free magnetic pickup accurately triggers this ignition with increased output from the amplifier, easily outperforming stock ignitions. These distributors will smooth out the engine's idle, improve starting, and perform at a much higher rpm. Their housings are machined from billet aluminum, using state-of-the-art CNC mills and lathes. For stability and endurance, an oversized steel shaft spins in a top-mounted sealed ball bearing for accuracy through the entire rpm range. Chevy models also feature an extra-long sintered bushing at the bottom and an extra oil tract machined into the bottom of the housing for improved lubrication. The tract delivers oil directly to the cam and distributor gears. All of the shafts receive a QPQ coating for low friction wear, and resistance against corrosion from humidity and ozone buildup. The Chevrolet models have also been tested by the Underwriter's Laboratory, and are certified to meet or exceed safety standards for marine ignition systems as set by the U.S. Coast Guard.
( 92 )
$499.95
—
$525.95
On Sale
MSD Pro-Billet Dual Sync EFI distributors feature high-quality dual Hall effect sensors, a QPQ coated precision billet shutter wheel, and distributor shaft that's guided by a sealed ball bearing. They also include a race-proven distributor gear, and a performance cap and rotor. The distributors are designed for use with Holley EFI systems; they may also fit other systems requiring a Hall effect sensor. Order the model recommended for your vehicle and engine application. (Note: an ignition adapter is required when Pro-Billet Dual Sync EFI distributors are utilized with Sniper EFI.) Features, specs, and parts may include: * CNC-machined billet aluminum housing * Precision-machined shutter wheel designed for improved accuracy at extreme engine rpm * Plug-and-play with Holley EFI * Can be used to trigger popular TBI fuel injection systems * Hall Effect sensor design provides precise timing control and noise immunity * Integrated LEDs allow for easy setup * Shutter wheel is pinned and welded to distributor shaft for superior reliability
( 17 )
$579.95
$302.95
—
$549.95
MSD Pro-Billet crank distributors are built specifically for racing engines with almost no room for a distributor, due to tunnel rams or blowers. These units are equipped with a special low-profile crab-style distributor cap, allowing them to fit into extremely tight areas. The housing features two optional O-rings at the bottom that improves oil control by preventing oil pressure loss. Also, a small oil bleed hole (located in the base) sprays oil on the distributor and camshaft gears to prevent excessive wear. Since these are racing distributors, there is an adjustable slip collar to make up for engines that have had the distance between the mounting surface and the gear modified. Crowning the Pro-Billet crank distributor is MSD's own crab cap. This incorporates spark plug-style terminals for a better connection and grip to the plug wires. Order the model recommended for your vehicle and engine application.
( 20 )
$449.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
