Availability
On Sale
MSD 8.5mm Super Conductor spark plug wire sets feature a special helically wound core that has just 40-50 ohms of resistance per foot—but with an RFI suppression equal to a 1,500 ohm wire. In fact, each foot of finished wire includes 40 ft. of tightly wound copper for superior conductivity. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective Electro Magnetic Interference "choke." This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. A tough, 8.5mm synthetic/silicone jacket over an extra-heavy glass braid and dielectric insulator keeps the current guided to the plugs. Underneath the high-temperature boots, dual crimp stainless steel terminals feature snap-locks to ensure a secure fit. Each set comes with clip-on cylinder markers for easy identification. MSD's 8.5mm Super Conductor wire sets are available in custom or universal-fit applications, assembled or not, with a variety of terminal and boot end options.
( 1974 )
$274.95
$107.05
—
$247.45
On Sale
MSD HEI coils increase spark energy when used with MSD HEI HEAT modules. Now you can replace your stock coil with these high-energy unitized coils for HEI distributors. They have low-inductance, high-temperature windings which charge the coil faster to give you increased spark energy at higher rpm. The premium epoxy filled construction is designed to withstand harsh race applications, as well as the wear and tear that daily usage dishes out, and still deliver more spark energy to the spark plugs.
( 36 )
$122.95
$110.65
On Sale
MSD Digital GM high-energy modules with rev limiters allow you to adjust the rpm limit between 5,000 and 9,000 rpm. True high-performance modules built for HEI distributors, they produce 50 percent higher coil drive currents than the stock module. This saturates the coil faster, which gives you more spark energy at top speeds. The results are increased horsepower and rpm range, and improved starting. When used with MSD's HEI coil, these plug-in modules create a potent high-energy spark to 9,000 rpm. MSD GM HEI modules replace all 4-pin modules used in HEI distributors with a vacuum advance canister. They can be used with factory, aftermarket, or MSD HEI distributors.
( 66 )
$177.95
$160.15
On Sale
The cap and rotor of any ignition system must be considered maintenance items. Just like when you change the oil and filter in your car, you should always replace your cap and rotor as a set. MSD makes it easy with these cap and rotor replacement kits. The correct rotor is already matched to the correct cap for you.
( 515 )
$126.95
—
$274.95
$114.25
—
$247.45
On Sale
high-quality MSD bronze distributor gears are machined from quality AMPCO 45 aluminum bronze containing 5% nickel. This material creates high strength gear teeth which are less prone to wear when used with high volume oil pumps but does not harm the cam like steel or iron gears. With the proper cam and gear combination you'll be sure to have flawless, extended performance in the harshest conditions.
( 93 )
$131.95
$118.75
On Sale
MSD Ignition's Multiple Spark Coils (MSC) will fit in place of the stock GM LS coils and connect directly to the factory connectors. Once installed, you'll have the power and performance of higher energy sparks, crowned with MSD's multiple spark discharge. Increased spark energy and voltage, along with multiple spark capabilities, help improve the combustion process of the fuel mixture to create an efficient burn. This results in improved throttle response, smooth idle and quick starts, plus increased high rpm performance!
( 26 )
$149.95
$112.46
On Sale
When tested against a competitor's coil, the MSD Pro Power coils produced 33 percent more current at the plug. They have an oil-filled insulated polyester case, an extra-tall high-tension spark plug tower to stop voltage leaks, and rubber shock mounts. They're designed for drag race use only, with MSD 7 and 8 Series ignitions.
( 41 )
$184.95
$166.45
On Sale
MSD 8.5 mm Race Tailored Super Conductor Wire Sets are designed to specifically fit race engines equipped with headers or MSD distributors. They feature wires that are custom cut to route behind the block, under the headers, and to the spark plugs. This routing gives the engine an extra clean appearance as well as protecting the wires from making contact with the engine. The wires have a special helically-wound core that has just 40-50 ohms of resistance per foot--but with the RFI suppression equal to a 1,500 ohm wire. In fact, each foot of finished wire features 40 feet of tightly wound copper for superior conductivity. A tough 8.5 mm synthetic/silicone jacket over an extra heavy glass braid and dielectric insulator keeps the current guided to the plugs. Underneath the high-temperature boots, stainless steel terminals feature snap locks to assure a secure fit.
( 13 )
$199.95
On Sale
MSD Atomic EFI billet fuel rails are the perfect complement for your Atomic AirForce intake manifold. Whether you're looking for just rails, or complete kits with all the necessary plumbing--these fuel rails will have you looking for any excuse to pop the hood. They feature a bright dip, black anodized finish with laser-etched logos and a 5/8 in. diameter fuel passage flow capacity for high-horsepower applications. Make your engine look as good as it performs with MSD Atomic EFI fuel rails. Features, specs, and parts may include: * Fuel rails are machined to accept large -8 (3/4 in.-16) O-ring fittings * Includes mounting brackets and hardware * Includes four -6 to 3/4 in.-16 O-ring adapters
( 1 )
$249.95
$224.95
Make installation a breeze with MSD ignition coil brackets. They're crafted from aluminum and are made for the specific purpose of keeping your coil braced.
( 6 )
$218.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
