Availability
On Sale
Holley Sniper EFI HyperSpark distributor kits were designed to make upgrading your ignition on a Sniper EFI-equipped engine simple. When installed concurrently with a new Sniper EFI system, the combination creates the easiest way to install EFI conversion on the market—and only four flying lead connections are required! The harness only requires one connection to a switched power source, battery positive, battery negative, and fuel pump power. The pre-terminated connectors and a built in 40A relay provides power to all of the components within the system. With the included Sniper EFI main harness you no longer need to run multiple wires to provide switched power for each individual component, which not only helps prevent wiring confusion, but it will also speed up your install time and clean up your engine bay. Simply route the harness and pre-terminated connectors to your HyperSpark coil, distributor, and ignition box and plug them in. Available for all popular engine combinations, these kits come with a distributor, coil, ignition box, and an integrated Sniper EFI harness. Order the application you need. Key features: * Plug-and-Play Sniper EFI main harness replaces the standard Sniper EFI harness with four loose leads, battery positive, battery ground, switched 12 V, and fuel pump power, for a simple and streamline installation * Designed for existing or new Sniper EFI installations (the HyperSpark Master Kit harness retains the same flying lead wire colors as the Sniper EFI main harness; new installations will not use the Sniper EFI standard harness or coil driver * Complete ignition system in a box, including: HyperSpark ignition box, HyperSpark ignition coil, HyperSpark distributor (for your application), and a plug-and-play main harness * HyperSpark distributors feature a Hall Effect crank trigger sensor providing a noise-free rpm signal to the Sniper ECU * Patented clear installation cap eliminates any confusion while installing the distributor * HyperSpark CD ignition box is seal and powder coated to be installed in the harshest of locations * External LED on HyperSpark CD Ignition box helps verify 12 V, cranking rpm, and low battery voltage * 135mJ of spark energy when used with the HyperSpark ignition coil, ensures complete combustion * Integrated ignition coil bracket simplifies mounting the Ignition coil * Ignition coil connector removes any doubt of loose connections at the Ignition coil * Enables timing control on a Sniper EFI Installation
( 22 )
$999.95
$898.95
On Sale
Holley G-body fuel system kits remove the guesswork when updating your G-body's system. Designed as a direct replacement for your factory fuel system, these kits contain everything required to go from fuel tank to engine bay. They are engineered for use with factory fuel line routing and mounting locations, creating a clean, OEM-like installation. Prepare your G-body with a bullet-proof fuel system for any EFI conversion with Holley fuel system kits. Features: * Pump gas and E85 compatible fuel system plumbing kit * 40 ft. of 6 AN nylon braided hose, enough to go from the tank to the fuel rails for both feed and return * Utilizes as many of the original sheet metal and chassis fuel system routing provisions with minimal to no drilling required * Electric fuel pump harness and relay wiring kit ensures the fuel pump receives the proper amperage, for improved reliability and consistent performance * Pre-calibrated fuel level sending unit works with factory fuel gauge for a simplistic installation—no guesswork about ohm range * Highly detailed installation instructions to guide you, step by step, along the installation process Kits include: * 350 lph EFI fuel pump module * Billet fuel filter * Fuel pressure regulator * Fuel pressure gauge * Nylon braided hose * AN fittings * Hardware * EFI-rated clamps * Fuel level sender * Fuel pump harness and relay wiring kit
( 2 )
$849.95
$763.95
On Sale
One of the most popular updates for an older vehicle is swapping out the carburetor for electronic fuel injection (EFI); but using an external pump to supply the high pressure needed for EFI can be a problem. External pumps are loud and often difficult to mount properly. Holley Sniper EFI conversion fuel tanks are the complete bolt-in solution for your EFI conversion. They're a direct-fit for a wide variety of specific applications, require no modifications, and include either a 255 lph or 400 lph submersible pump, a fuel level sender, and internal baffles. For the fuel you need with in-tank quietness, order a Holley Sniper EFI conversion fuel tank. Features include: * 255 lph model supports up to 550 hp * 400 lph model supports up to 750 hp * 60 psi at 13.5 V with a 10.4 amp draw * Made of coated, galvanized steel that is also silver powdercoated for corrosion protection * Fuel pump hanger assembly included * Sender has 1/4 in. NPT supply and return line ports for easy fuel line connection * Barbed vent fitting * Sending units have the correct ohm range for factory gauges * Fuel pump and sender are recessed into the tank * EFI-style tank baffling includes a 4.3L internal fuel tray to prevent starvation * Fits and looks like an OE tank when installed * Include new tank straps, where applicable
( 109 )
$875.95
$763.95
—
$949.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
