Availability
On Sale
Holley Sniper EFI HyperSpark distributor kits were designed to make upgrading your ignition on a Sniper EFI-equipped engine simple. When installed concurrently with a new Sniper EFI system, the combination creates the easiest way to install EFI conversion on the market—and only four flying lead connections are required! The harness only requires one connection to a switched power source, battery positive, battery negative, and fuel pump power. The pre-terminated connectors and a built in 40A relay provides power to all of the components within the system. With the included Sniper EFI main harness you no longer need to run multiple wires to provide switched power for each individual component, which not only helps prevent wiring confusion, but it will also speed up your install time and clean up your engine bay. Simply route the harness and pre-terminated connectors to your HyperSpark coil, distributor, and ignition box and plug them in. Available for all popular engine combinations, these kits come with a distributor, coil, ignition box, and an integrated Sniper EFI harness. Order the application you need. Key features: * Plug-and-Play Sniper EFI main harness replaces the standard Sniper EFI harness with four loose leads, battery positive, battery ground, switched 12 V, and fuel pump power, for a simple and streamline installation * Designed for existing or new Sniper EFI installations (the HyperSpark Master Kit harness retains the same flying lead wire colors as the Sniper EFI main harness; new installations will not use the Sniper EFI standard harness or coil driver * Complete ignition system in a box, including: HyperSpark ignition box, HyperSpark ignition coil, HyperSpark distributor (for your application), and a plug-and-play main harness * HyperSpark distributors feature a Hall Effect crank trigger sensor providing a noise-free rpm signal to the Sniper ECU * Patented clear installation cap eliminates any confusion while installing the distributor * HyperSpark CD ignition box is seal and powder coated to be installed in the harshest of locations * External LED on HyperSpark CD Ignition box helps verify 12 V, cranking rpm, and low battery voltage * 135mJ of spark energy when used with the HyperSpark ignition coil, ensures complete combustion * Integrated ignition coil bracket simplifies mounting the Ignition coil * Ignition coil connector removes any doubt of loose connections at the Ignition coil * Enables timing control on a Sniper EFI Installation
( 21 )
$999.95
$898.95
On Sale
Do you need to upgrade your ignition system due to a recent Sniper EFI installation, but have no idea which option is best? Introducing Holley Sniper EFI HyperSpark distributors. These billet distributors use a hall-effect crank signal sensor, providing a noise-free RPM signal to the Sniper ECU. HyperSpark distributors include a patented clear installation cap that eliminates any confusion when installing the distributor. They're an easy plug-and play solution to add timing control and complete your Sniper EFI installation. Many options are available; choose the model recommended for your year/make and engine application.
( 127 )
$449.95
—
$699.95
$403.95
—
$628.95
On Sale
With Holley Sniper throttle bodies, Holley engineers went back to the drawing board to build the ultimate air valve for your engine! They feature enlarged bore sizes, allowing for increased airflow to support your higher horsepower needs. A progressive throttle pulley enhances low-speed drivability, and a double return spring provides solid and secure throttle control feel. These units are maximized for your application, with a 4-bolt style mounting pattern; most models include bolts and gaskets. Order the throttle body designed for fitment with your year/make and engine family.
( 39 )
$249.95
—
$349.95
$192.95
—
$241.15
On Sale
Holley Sniper offers OE-style 255 lph EFI fuel pump modules for a wide range of vehicles, including many Chevy, Pontiac, Buick, Oldsmobile, GMC, Ford, Mercury, Jeep, Dodge and Plymouth cars and trucks from the 1950s, '60s, '70s, and '80s. These in-tank modules are high-pressure units that flow 255 liters per hour (LPH) and are capable of supporting electronic fuel injection (EFI) engines producing up to 550 hp. A pre-calibrated fuel level sending unit designed to work with the factory fuel gauge for this application is included. Each module also features a HydraMat filter which has a unique internal reservoir that keeps fuel available at the pick-up and also provides protection from contaminates. Fuel pressure is internally regulated to 58 psi, eliminating the added expense and effort of purchasing and installing an external fuel pressure regulator; no separate return line is required because these modules return excess fuel right inside the tank! The Holley Sniper EFI fuel pump module was designed as a direct replacement for your factory pick-up and sending unit. There's no need to purchase a custom EFI fuel tank. You can even retain the factory fuel hard line—just connect the outlet of the pump module to the hard line on your vehicle with EFI-rated fuel hose and hose clamps available in the Earls Vapor Guard line.
( 10 )
$399.95
$359.95
On Sale
Holley Sniper EFI 2GC large bore fuel injection systems let you convert your classic 2GC large bolt pattern carburetor to EFI. These units offer superior throttle response and WOT power over the carb—and you will likely experience increased fuel economy. Put an end to cold start issues, hesitations, vapor lock, and flooding with the accuracy of EFI. You can also use the Sniper EFI 2GC to control the ignition timing, taking electronic fuel injection to the next level. These Holley upgrade systems feature two 100 lb./hr. fuel injectors capable of supporting 350 hp on naturally aspirated engines. The Sniper EFI systems are also available in a Master Kit option, which includes 20 ft. of fuel hose, two filters, one high-pressure EFI fuel pump, and all required fittings for a complete EFI fuel system conversion. Standard and Master Kit systems are available in a choice of throttle body finishes. Standard Sniper EFI system features: * Bolt-on 2GC large bore carburetor replacement * Universal throttle lever with TH350, 700R4 and 200-4R kickdown provisions * Throttle body-mounted ECU; no extra boxes to mount * Only four wiring connections required: Battery +, battery -, switched ignition, and rpm * Internal fuel pressure regulator eliminated the hassle of plumbing an external fuel pressure regulator (preset to 58.5 psi) * Integrated ignition timing control (with MSD Pro Billet, Holley Dual Sync, or Holley Hyperspark distributors) * High-resolution full-color touch screen for initial setup, tuning, and gauge displays * Simple Calibration Wizard (answer a few questions about your engine and it creates the base map, then starts tuning on its own!); NO laptop required * Self-tuning ECU means you don't have to be a computer/tuning wiz to have EFI * The included Genuine Bosch LSU 4.9 wideband oxygen sensor provides real-time Fuel Map Learn * OEM-style TPS/IAC and fuel pressure regulator—for years of dependable service * Included clamp-on oxygen sensor kit for 2 in. exhaust ensures a leak-free oxygen sensor installation, with stainless steel T-bolt clamps and a stainless steel (weldable) oxygen sensor flange * Systems are an ideal conversion for 1974-78 Chevrolet, GMC, Oldsmobile, and Pontiac vehicles that came with a Rochester 2GC large bore carburetor.
Not Yet Reviewed
$1,299.95
—
$1,599.95
$1,168.95
—
$1,438.95
On Sale
One of the most popular updates for an older vehicle is swapping out the carburetor for electronic fuel injection (EFI); but using an external pump to supply the high pressure needed for EFI can be a problem. External pumps are loud and often difficult to mount properly. Holley Sniper EFI conversion fuel tanks are the complete bolt-in solution for your EFI conversion. They're a direct-fit for a wide variety of specific applications, require no modifications, and include either a 255 lph or 400 lph submersible pump, a fuel level sender, and internal baffles. For the fuel you need with in-tank quietness, order a Holley Sniper EFI conversion fuel tank. Features include: * 255 lph model supports up to 550 hp * 400 lph model supports up to 750 hp * 60 psi at 13.5 V with a 10.4 amp draw * Made of coated, galvanized steel that is also silver powdercoated for corrosion protection * Fuel pump hanger assembly included * Sender has 1/4 in. NPT supply and return line ports for easy fuel line connection * Barbed vent fitting * Sending units have the correct ohm range for factory gauges * Fuel pump and sender are recessed into the tank * EFI-style tank baffling includes a 4.3L internal fuel tray to prevent starvation * Fits and looks like an OE tank when installed * Include new tank straps, where applicable
( 109 )
$949.95
$763.95
—
$853.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
