JavaScript Disabled

Your JavaScript appears to be disabled. JavaScript is necessary for various functions, such as order checkout, to operate on this web site. Please ensure that JavaScript is enabled.

Outdated Internet Browser Detected

Your web browser appears to be out of date. Soon you will not be able to create a secure connection to our web site using TLS 1.0. Please upgrade your browser from current version( ). Learn more about TLS.

Always Save the Most at Summit!
In-Store Pickup Location

MSD 8.5mm Super Conductor Spark Plug Wire Sets 35593

Make sure this fits your vehicle:

Spark Plug Wires, Super Conductor, Spiral Core, 8.5mm, Black, 90 Degree Boots, Chevy, Small Block, V8, Set

Estimated Ship Date: Loading...Processing Today Would you rather pick it up? Select Location

Hazardous Material Warning
WARNING
WARNING: Cancer and Reproductive Harm For more information, visit www.P65warnings.ca.gov.

Brand: MSD Ignition

Manufacturer's Part Number: 35593

Part Type: Spark Plug Wire Sets

Product Line: MSD 8.5mm Super Conductor Spark Plug Wire Sets

Summit Racing Part Number: MSD-35593

UPC: 085132355938

Assembled: Yes

Distributor Terminal Ends: Male/HEI

Distributor Boot Color: Gray

Distributor Boot Material: Silicone

Spark Plug Boot Ends: Eight 90 degree

Spark Plug Boot Color: Gray

Spark Plug Boot Material: Silicone

Wire Color: Black

Diameter (mm): 8.50mm

RFI Suppression: Yes

Coil Wire Included: Yes

Conductor Style: Spiral core

Spark Plug Wire Resistance: 50 ohms/ft.

Quantity: Sold as a set.

Notes: Wires route below headers/exhaust manifolds. Included coil wire has female ends on both ends of it.

In-Store Pickup: Choose In-store pick-up (OH, NV, GA, TX) on our web site.

MSD 8.5mm Super Conductor spark plug wire sets feature a special helically wound core that has just 40-50 ohms of resistance per foot—but with an RFI suppression equal to a 1,500 ohm wire. In fact, each foot of finished wire includes 40 ft. of tightly wound copper for superior conductivity. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective Electro Magnetic Interference "choke." This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. A tough, 8.5mm synthetic/silicone jacket over an extra-heavy glass braid and dielectric insulator keeps the current guided to the plugs. Underneath the high-temperature boots, dual crimp stainless steel terminals feature snap-locks to ensure a secure fit. Each set comes with clip-on cylinder markers for easy identification. MSD's 8.5mm Super Conductor wire sets are available in custom or universal-fit applications.

Warranty

Most Helpful Reviews Review This Product

15 Customer Reviews for MSD Ignition 35593 - MSD 8.5mm Super Conductor Spark Plug Wire Sets

Average Customer Review

5 Star

(8)

4 Star

(5)

3 Star

(0)

2 Star

(1)

1 Star

(1)

+See All 15 Reviews

Not cut to correct length.

Summit RacingSummit Racing Verified Purchase

MSD-35593
I purchased an MSD ready to run distributor, blaster coil and plug wires to suit my '66 327 Impala SS. Very satisfied with the dizzy and coil but the 35593 Plug Wire Sets had me pulling my hair out and you may have heard me cursing from down under. The longest 4 wires that run to plugs 1,2,3 and 4 were a full 6" shorter than my originals which meant I was unable to run them in the correct location, they are too close to the exhaust manifolds and run the shortest possible route, still only have approx half inch of slack at best. The rear 4 cylinder wires were the same length as the originals. I suggest they check the Quality Control in this department. Tony, Australia. ...read more

2 of 2 found this review helpful.

report abuse

Report Abuse X

If you feel that this review is inappropriate and should be removed from the site, report it to us by clicking the "Report Abuse" button below.

Cancel

Reviewer: from Australia

Date: September 07, 2014

Appearance
Ease of Installation
Price/Value
Quality

1984 Chevrolet k-10 4×4

Summit RacingSummit Racing Verified Purchase

MSD-35593
I installed these on my 84 Chevrolet pickup 4x4 k-10 with a 350 motor and 700 R-4 transmission with headers. The installation was easy and the wire lengths were perfect. I had no issues installing these in a very neat organized way and the clearance from the headers was also good. They are great looking also.

0 of 0 found this review helpful.

report abuse

Report Abuse X

If you feel that this review is inappropriate and should be removed from the site, report it to us by clicking the "Report Abuse" button below.

Cancel

Reviewer: from NY

Date: September 18, 2018

Appearance
Ease of Installation
Price/Value
Quality

1980 corvette 5th # 6 ,5.7,engine,no FI

Summit RacingSummit Racing Verified Purchase

MSD-35593
The wires were long enough to fit with shields. They looked and worked well. They must be well shielded because my wire tester did not work with them.They are such a pain to change I wanted a very good set. I hope this is the last set I change on the corvette. JP

0 of 0 found this review helpful.

report abuse

Report Abuse X

If you feel that this review is inappropriate and should be removed from the site, report it to us by clicking the "Report Abuse" button below.

Cancel

Reviewer: from OH

Date: September 12, 2018

Appearance
Ease of Installation
Price/Value
Quality

MSD spark plug wires

Summit RacingSummit Racing Verified Purchase

MSD-35593
this is a good set of wiress, but it looks like you wouldn,t have to buy a certain set of wires to run a MSD ignition

0 of 0 found this review helpful.

report abuse

Report Abuse X

If you feel that this review is inappropriate and should be removed from the site, report it to us by clicking the "Report Abuse" button below.

Cancel

Reviewer: from WV

Date: August 24, 2018

Appearance
Ease of Installation
Price/Value
Quality

MSD Plug Wires

Summit RacingSummit Racing Verified Purchase

MSD-35593
Great quality, the length of the wires were great except for the one used for the #2 wire, it could have been about 4 to 6 inches longer for a better fit. These were install on a 79 Corvette with wires installed above the headers not underneath as originally installed with factory exhaust manifold.

0 of 0 found this review helpful.

report abuse

Report Abuse X

If you feel that this review is inappropriate and should be removed from the site, report it to us by clicking the "Report Abuse" button below.

Cancel

Reviewer: from TN

Date: July 26, 2018

Appearance
Ease of Installation
Price/Value
Quality
Questions & Answers Ask a Product Question

There are no questions for this product.

Some parts are not legal for use in California or other states with similar laws / regulations

Back To Results
Email this page
Sign Up for Email X