2016 Air & Fuel Delivery - In Stock Filter Options - Vendor In Stock Filter Options - Free Shipping on Orders Over $109 at Summit Racing

Fleece Performance Cheetah FMW Turbochargers

Amplify your driving experience with a Fleece Performance Cheetah turbocharger. Featuring a Fleece exclusive 63mm FMW compressor wheel and a high-flow turbine wheel, these turbos are capable of supporting up to 650 rear wheel horsepower without sacrificing any drivability. These drop-in replacements offer smooth and quick throttle response with big top-end power. Whether you're towing, racing, sled pulling, or just driving to work, the Cheetah will get the job done. Order the model recommended for your truck.

3.0 out of 5 stars ( 2 )

$2,999.00

Injector Dynamics ID1750x Fuel Injectors

The best just got better! Injector Dynamics ID1750x fuel injectors are a built-to-spec motorsport injector, offering optimization of critical operating parameters important to you, the motorsport tuner. Built on the evolution of the ID1700 and X Series, these fuel injectors are a drastic improvement over previous series from Injector Dynamics. Compared to the 1700, the 1750x offers: higher dynamic flow rate with no increase in minimum fuel mass, better cylinder to cylinder balance at low pulse widths, and improved pressure sensitivity—all while retaining the same "compatible with everything but dirt" corrosion resistance that made the ID1700 famous. Plus, a unique magnetic circuit, resulting from a lengthy development program, makes the ID1750x immune to voltage and pressure sensitivity problems that plague other high impedance high flow injectors. Order the set of fuel injectors recommended for your vehicle. Key features and benefits include: * Compact body design allows fitment in a variety of applications * Higher dynamic flow rate with no decrease in minimum fuel mass * Better cylinder to cylinder balance at low pulse widths * Improved pressure sensitivity * Corrosion resistance makes these fuel injectors compatible with Methanol/Ethanol/MTBE/Nitromethane and all known Hydrocarbon fuels * Unique magnetic circuit makes the ID1750x immune to voltage and pressure sensitivity problems that plague other high impedance high flow injectors * Narrow spray pattern—minimal wall wetting promotes quick response and smooth running * Does not require extended linearity at low flow rates

Not Yet Reviewed

$2,419.20

On Sale

Summit Racing™ Turbocharger Replacement Kits

Summit Racing™ turbocharger replacement kits are engineered packages with upgraded components needed to replace your high-mileage stock turbos. These one-click kits give you what you need to do the job correctly and address some of the shortcomings of the factory system. Check out the features below: * Brand new direct-fit turbos * Cast stainless exhaust manifolds improved flow and durability * Inconel manifold studs and stainless hardware kit * MLS stainless gaskets * Improved coolant line kits

Not Yet Reviewed

$2,341.92

$2,299.99

On Sale

Summit Racing™ LS CNC Billet Intake Manifolds

Our Summit Racing™ LS CNC billet intake manifolds look great and are made to take whatever you can throw at them. They are capable of handling 2,000 horsepower and over 300 psi of boost! Their plenums and bolt-on runners are CNC machined billet aluminum and will not distort or warp under boost. These intakes can accept up to 102mm throttle bodies and include hardware, gaskets, and an -8 AN fuel rail kit.

Not Yet Reviewed

$2,399.99

Fleece Performance Cheetah FMW VNT Turbochargers

Fleece Performance offers Cheetah FMW VNT turbochargers for a variety of diesel trucks to enhance your driving experience. These drop-in replacements come with a Fleece-engineered 63mm FMW compressor wheel and high-flow Cheetah turbine wheel. You'll enjoy the spool-up and throttle response of a small turbo and still get the big top-end power you're looking for. Rated at up to 650 rear wheel horsepower (depending on model), this is the ultimate combination for dual-purpose applications. If you're towing during the week and sled pulling on the weekend, the 63mm FMW VNT Cheetah is just the ticket. Order the turbo model recommended for your vehicle. Additional details: * Stock appearing: Uses the stock housings with updated internals. This allows you to keep all factory systems intact, yet enables you to safely run 40 psi of boost. No aftermarket components or modifications needed for installation. * Proven Technology: Built with genuine Garrett Turbocharger parts. They feature upgraded shaft bearings and 360 degree thrust bearings. * Powerful Yet Responsive: Turbochargers spool like stock, thanks to the variable nozzle technology (VNT) which allows the turbo to act smaller upon spool-up and then open up to flow more exhaust on the top end. * Exclusive FMW wheel technology: – Forged milled wheels – Faster spool-up – Increased throttle response – Broader torque curve

5.0 out of 5 stars ( 2 )

$2,649.00

Holley Terminator X MAX Stealth 4150 58X LS EFI Fuel Injection Systems

Holley Terminator Max X Stealth 4150 58X LS EFI systems feature four 100 lbs./hr. fuel injectors capable of supporting up to 650 hp naturally aspirated or 600 hp on forced induction applications. The Terminator X ECU provides fuel maps that self-learn and integrated ignition timing control, yielding improved idle stability, drivability, and horsepower at wide-open throttle! Holley Terminator Max X Stealth 4150 58X LS EFI fuel injection systems also include transmission kick-down provisions for GM TH350/400, 200R4/700R4, and Ford C4/C6 applications, as well as plug-and-play transmission control for GM 4L60 and 4L80 applications. System features include: * All wiring exits below the fuel injector bowls for a complete stealth installation * Air entry machined to fit most stock-style air cleaners with air cleaner locator provisions * Integrated ignition timing control offers plug-and-play with factory LS coil sub-harness and OEM LS coils (no external boxes/modules needed to run coil near plug) * High-resolution, full-color touchscreen for initial setup, tuning, and gauge displays * Simple calibration wizard—no laptop required * Four inputs (12 V, ground, 5 V, and frequency) for things such as additional pressure sensors, or activation triggers for nitrous activation, or a trans brake (fuel and oil pressure inputs are pre-terminated) * Four outputs (ground, PWM -) for accessories such as fans, boost control, nitrous control, IAC kit, and more * Genuine Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * OEM-style TPS/IAC for years of dependable service * Available in three finishes: shiny, black, and gold * Compatible with Holley EFI digital dashes, gauges, and fuel system accessories

5.0 out of 5 stars ( 1 )

$2,819.95

Edelbrock Pro-Flo 4 EFI Systems

Edelbrock Pro-Flo 4 EFI systems provide you with a high performance traditional-style intake and 4150-style throttle body. Unlike regular throttle body EFI systems, Pro-Flo 4 features the fuel rails and individual injectors for each cylinder mounted on the manifold. This Edelbrock design produces the best fuel atomization and distribution for the ultimate performance, as well as delivering the most control and the most efficient way to deliver fuel to your engine. Along with innovative design, Pro-Flo 4 systems have the latest technology with an all-new ECU, and even more features for advanced tuning, with the key being their exclusive E-Tuner app with base calibrations developed on their dyno. Edelbrock Pro-Flo 4 EFI systems include and feature: * Engine Control Unit with faster processor and upgraded Bluetooth chip in a thinner waterproof design * Fully assembled intake manifold with air valve, fuel rails, and injectors * Fully assembled OEM high-quality wiring harness with pre-terminated connectors and labeled connection for a simplified installation * E-Tuner application for setup and engine monitoring * Wideband oxygen sensor * Distributor (not included with LS kits) * Gaskets and hardware * Installation instructions * Ready to run out of the box with pre-loaded calibrations * Self-learning technology--no tuning experience or laptop tuning required * Ignition control--adjust ignition curve with the E-Tuner 4 App for optimal performance and mpg * Offered with multiple fuel injector choices * Now boost compatible up to 15 psi by switching to a 2-bar MAP sensor and downloading the new firmware update from Edelbrock for free! It is recommended to regularly check for firmware updates even if not utilizing boost control. * Systems automatically compensate for altitude and weather changes * E-Tuner 4 app with Bluetooth connectivity between ECU and Android phone or tablet. Includes multiple dash display configurations for monitoring engine vitals and performance; multiple control functions including two adjustable cooling fan outputs, idle speed, AFR set points, acceleration fuel tuning, ignition control, cold start fuel, and cranking fuel.

4.11 out of 5 stars ( 127 )

$2,266.95

—

$2,555.95

Fleece Performance LML CP3 Conversion Kits

Why convert your LML's fuel system from a CP4 to a CP3? Since its introduction, the CP4 has proven to be less reliable and less capable than the CP3 used in previous Duramax platforms—resulting in costly repairs for owners when a CP4 fails. You can improve your LML Duramax's reliability and fueling capability, as well as avoid costly failure with Fleece Performance LML CP3 conversion kits. They provide OEM fit-and-finish features, like Fleece's exclusive molded hoses for the fuel feed and return, high flow CP3 fuel fittings, and their valley feed line to support aftermarket lift pump applications. Fleece Performance LML CP3 conversion kits are offered with or without pump and the pump kits come in two different style pumps—a Bosch CP3 injection pump or Bosch CP3 pump with heavy-duty 10mm cam. Choose the kit that is right for you. All kits include: * CP3 to rail high pressure fuel line * High-flow CP3 feed and return fuel fittings * Preformed fuel feed and return fuel hoses * CP3 mounting adapter * Dosing injector distribution block, feed and return lines * FCA extension harness * Low pressure fuel feed line * Hardware kit

Not Yet Reviewed

$2,599.00

FiTech Nitro-Port Cast LS3 750 HP Fuel Injection Systems

FiTech Fuel Injection proudly introduces the Nitro-Port Cast LS3 750 hp fuel injections systems, combining FiTech's cutting-edge EFI technology with the all-new Nitro-Port Series intake manifold. Designed for serious street builds and track performers, these complete EFI systems deliver reliable horsepower and modern drivability in one powerful package. At the heart of each kit is the Nitro-Port cast intake manifold, engineered with a low-profile modular runner design, short runners for high-rpm performance, -8 AN fuel rails, pre-drilled and tapped nitrous/water injection port, and support for 92mm, 102mm, and drive-by-wire throttle bodies (drive-by-throttle bodies coming soon). Rear-mounted vacuum ports and MAP sensor location keep installations clean and streamlined. Every Nitro-Port LS EFI System includes: * FiTech ECU * Complete wiring harness * Full set of sensors (including MAP, IAT, CTS, and more) * Dual Wideband O2 sensors * Touchscreen handheld controller for setup and tuning * And of course, the Nitro-Port intake manifold These plug-and-play systems take the guesswork out of EFI conversions while delivering exceptional performance and adjustability right out of the box. Whether you're swapping an LS into your muscle car or building a high-horsepower track weapon, the FiTech Nitro-Port LS EFI Systems provide the power, tuning control, and quality FiTech is known for.

Not Yet Reviewed

$2,245.00

—

$2,445.00

Edelbrock Pro-Flo 4 XT EFI Systems

Edelbrock Pro-Flo 4 XT EFI systems provide you with a high performance Pro-Flo XT-style intake and 90mm throttle body. Unlike regular throttle body EFI systems, Pro-Flo 4 features the fuel rails and individual injectors for each cylinder mounted on the manifold. This Edelbrock design produces the best fuel atomization and distribution for the ultimate performance, as well as delivering the most control and the most efficient way to deliver fuel to your engine. Along with innovative design, Pro-Flo 4 systems have the latest technology with an all-new ECU, and even more features for advanced tuning, with the key being their exclusive E-Tuner app with base calibrations developed on their dyno. Edelbrock Pro-Flo 4 XT EFI systems include and feature: * Engine Control Unit with faster processor and upgraded Bluetooth chip in a thinner waterproof design * Fully assembled XT intake manifold with air valve, fuel rails, and injectors * Fully assembled OEM high-quality wiring harness with pre-terminated connectors and labeled connection for a simplified installation * E-Tuner application for setup and engine monitoring * Wideband oxygen sensor * Distributor * Gaskets and hardware * Installation instructions * Ready to run out of the box with pre-loaded calibrations * Self-learning technology--no tuning experience or laptop tuning required * Ignition control--adjust ignition curve with the E-Tuner 4 App for optimal performance and mpg * Offered with multiple fuel injector choices * Now boost compatible up to 15 psi by switching to a 2.5-bar TMAP sensor and downloading the new firmware update from Edelbrock for free! It is recommended to regularly check for firmware updates even if not utilizing boost control. * Systems automatically compensate for altitude and weather changes * E-Tuner 4 app with Bluetooth connectivity between ECU and Android phone or tablet. Includes multiple dash display configurations for monitoring engine vitals and performance; multiple control functions including two adjustable cooling fan outputs, idle speed, AFR set points, acceleration fuel tuning, ignition control, cold start fuel, and cranking fuel.

4.59 out of 5 stars ( 22 )

$2,645.95

—

$2,754.95

FiTech Nitro-Port Cast LS1 1000 HP Fuel Injection Systems

FiTech Fuel Injection proudly introduces the Nitro-Port Cast LS1 1000 hp fuel injections systems, combining FiTech's cutting-edge EFI technology with the all-new Nitro-Port Series intake manifold. Designed for serious street builds and track performers, these complete EFI systems deliver reliable horsepower and modern drivability in one powerful package. At the heart of each kit is the Nitro-Port cast intake manifold, engineered with a low-profile modular runner design, short runners for high-rpm performance, -8 AN fuel rails, pre-drilled and tapped nitrous/water injection port, and support for 92mm, 102mm, and drive-by-wire throttle bodies (drive-by-throttle bodies coming soon). Rear-mounted vacuum ports and MAP sensor location keep installations clean and streamlined. Every Nitro-Port LS EFI System includes: * FiTech ECU * Complete wiring harness * Full set of sensors (including MAP, IAT, CTS, and more) * Dual Wideband O2 sensors * Touchscreen handheld controller for setup and tuning * And of course, the Nitro-Port intake manifold These plug-and-play systems take the guesswork out of EFI conversions while delivering exceptional performance and adjustability right out of the box. Whether you're swapping an LS into your muscle car or building a high-horsepower track weapon, the FiTech Nitro-Port LS EFI Systems provide the power, tuning control, and quality FiTech is known for.

Not Yet Reviewed

$2,245.00

—

$2,399.00

BD Diesel Remanufactured Turbo Head Units

BD Diesel remanufactured turbo head units use the latest in aerodynamic technology and materials that feature lightweight, extended-tip compressor wheels with high-flow blade design characteristics for improved throttle response time. They offer cooler exhaust temperatures, improved engine brake retarding power, and the most rugged bearing system in the turbo industry. They feature a new look with natural finished cast aluminum that meets the highest of standards. If you're looking for a remanufactured turbo head unit that will give you consistent, dependable performance, BD Diesel remanufactured turbo head units won't let you down.

Not Yet Reviewed

$2,095.00

—

$3,036.00

BD Diesel Iron Horn Cummins Turbo Kits

Increase the horsepower in your Cummins with a BD Diesel Iron Horn Cummins turbo kit. These packages are available for a variety of specific year, make, model, and engine applications. Features and benefits include: * Increased airflow for more power, response, and reliability * Replace your factory turbo with a 300 Series SX-E BorgWarner T4 flange turbo * Includes a BD Performance Plus exhaust manifold and gaskets * No extra piping required; turbo drops into place for an easy, clean installation

5.0 out of 5 stars ( 1 )

$2,094.00

—

$2,296.00

FiTech Ultimate LS EFI 500 HP Fuel Injection Systems

FiTech has some of the best-engineered and priced throttle body systems on the market. Their LS EFI 500HP fuel injection systems bring incredible ingenuity to the market. FiTech fabricated many aluminum parts for these systems, including the low-profile 92mm billet throttle body, high-volume billet fuel rails, and an intake manifold with 1,500 to 6,500 rpm powerband and 3mm construction. Sequential spark and fuel control mates 36 lbs./hr. injectors, a plug-and-play wiring harness, and a color touchscreen self-learning ECU. This allows for programing two fan control outputs, most tach and speedometer output drivers, and target AFR and timing on the fly. A suction cup mounting bracket puts the controllers at your fingertips and allows for impressive visual aids. The optional transmission control feature is suitable for 4L60, 4L65, 4L70, or 4L80 GM transmissions. FiTech LS EFI 500HP fuel injection systems with transmission controller provide impressive power and performance, while allowing you to save a little green for your next tires. Additional features: * Black anodized aluminum parts for style and corrosion resistance * High-flow, cable-operated throttle body * Bosch wideband-controlled * Stainless oxygen sensor bung * Compatible with car and truck coils * AN fittings and fuel crossover * Works with custom cams * Designed for applications making at least 6 in. of vacuum at idle * 24X and 58X crank and cam compatible * Programmable touchscreen hand-held controller with data log features

3.21 out of 5 stars ( 42 )

$2,107.00

—

$2,633.99

FiTech Ultimate LS 1,000 HP EFI Fuel Injection Systems

FiTech Ultimate LS EFI 1,000 HP fuel injection systems with 102mm throttle body are a complete self-tuning induction system designed for everyone from the do-it-yourself hot rodder to the professional EFI tuner! These Ultimate EFI intake manifold kits are ready to go with everything needed to complete the induction system of your LS engine and get you on the road easily and faster than any system on the market today. So, you can forget about sourcing mismatched parts and cutting and splicing old harnesses and re-flashed ECU's from another unknown tuner source. FiTech has you covered with these complete kits, and they've taken the work out of getting your new or pull-out LS up and running in a flash! Small Block V8 GEN III/IV LS-based Chevrolet street and performance engines with a 1,500-6,500 rpm power-band up to 1,000 hp to the flywheel and contains a 3-bar MAP sensor for power adder applications that supports up to 30 psi of boost. Additional product features: * Low-profile, 102mm inlet, fabricated 3mm thick aluminum sheet metal TIG-welded intake manifold with 1,500-6,500 rpm power-band up to 1,000 hp to the flywheel and contains a 3-bar MAP sensor for power adder applications that supports up to 30 psi of boost * Billet fuel rails with AN fittings and fuel crossover * Self-learning ECU with touch screen controller for easy setup and configuration * Sequential fuel and spark control with individual cylinder trim * Dual Bosch wideband with dual trim control (self-learning) * 3-bar MAP sensor automatically detects up to 30 psi boost * Stainless oxygen sensor bung (clamp or weld-on) * 24X and 58X crank and cam compatible * Two programmable fan control outputs * TPS–IAC Sensor * Tach output driver for most tachometers (5 V) * Output driver for most speedometers * On-the-fly programmable target AFR and timing (if desired) * 80 lbs./hr. flow-matched injectors * Fuel pump relay output * Custom wire harness (uses factory coil pack sub harness) * Knock sensor control Note: This kit is not carb approved for use on emission-controlled vehicles. It is not legal for use on pollution-controlled vehicles. This system is designed to control the EFI and ignition on LS-based engines being retrofit into older vehicles that do not require emission controls.

5.0 out of 5 stars ( 1 )

$2,245.00

—

$2,689.00

FiTech Ultimate Rebel LS 750 HP EFI Fuel Injection Systems

FiTech Ultimate Rebel LS 750 hp EFI fuel injection systems are available with or without a transmission control. These cutting-edge fuel injection solutions combine high performance with a sleek and refined design. Building upon the success of the renowned FiTech Ultimate LS EFI system, the Rebel LS takes innovation a step further with its distinctive cleaner profile and enhanced features, making it the ultimate choice for modern engine conversions. Designed for enthusiasts seeking both power and aesthetics, the Ultimate Rebel LS EFI system redefines the look and performance of your LS-powered vehicle. The standout feature of the Rebel LS system is its sleek and streamlined appearance, which seamlessly integrates with the engine bay, providing a cleaner and more polished aesthetic. The redesigned fuel rail bracket adds to the visual appeal, offering a fresh and modern touch that complements any engine setup. Beneath its striking exterior, the Ultimate Rebel LS EFI system boasts the same advanced technology that FiTech is known for. Experience exceptional fuel delivery and engine control, optimizing your vehicle's performance and efficiency. These systems are tailored to LS engine conversions, ensuring a hassle-free installation process while delivering consistent and reliable results. Key features include: * Cleaner profile: The Ultimate Rebel LS EFI system is engineered with a refined design that seamlessly integrates into your engine bay, elevating the visual appeal of your vehicle * Thicker gauge manifold provides quieter injection * Redesigned fuel rail bracket: The innovative fuel rail bracket design not only enhances the appearance but also adds a touch of sophistication to your engine compartment * Advanced fuel injection technology: Benefit from FiTech's cutting-edge fuel injection technology, ensuring precise fuel delivery and optimized engine performance * Effortless installation: Designed specifically for LS engine conversions, the Rebel LS system offers a user-friendly installation process that minimizes downtime * Optimized performance: Unlock the full potential of your LS-powered vehicle with improved throttle response, increased horsepower, and better fuel efficiency * The most complete kit on the market; includes manifold, ECU, sensors, throttle body, harness, fuel rails, fuel pressure regulator, throttle cable brackets, and more * Boost/Nitrous compatibility: Equipped with 3 Bar MAP sensor (27 psi) * E85 compatible Kit contents: (1) Rebel LS1, LS2, LS6 low-profile intake manifold with MAP and IAT port (1) Ultimate LS 102mm throttle body with sensors (8) 36 LB injectors (1) LS ECU (1) LS1 fuel rail kit (1) Primary LS harness (2) EV1 injector sub harness (1) Oxygen sensor extension sub harness (1) 3 Bar MAP sensor (1) IAT sensor (1) LS1/LS2 knock sensor harness (1) Go EFI clamp-on oxygen sensor bung kit (1) Handheld monitor for ultimate LS (1) FiTech handheld cable (1) FiTech USB to USB C cable (2) FiTech oxygen sensors (1) Premium magnetic hand-held mount (1) Rebel intake throttle cable bracket with round hole (1) Rebel intake throttle cable bracket with stock GM cable notch (1) Go Fuel tight fit regulator with pressure gauge

Not Yet Reviewed

$2,190.00

—

$2,997.99

BD Diesel Screamer Turbochargers

BD Diesel Screamer turbochargers may offer a stock drop-in installation and appearance, but they are anything but stock! They feature a larger ballistic billet compressor wheel and BD's exclusive turbine profile that results in reduced backpressure and increased turbine flow compared to the competition. You get more potential maximum power output, right up to 690 hp with performance modifications. Each turbocharger is high-speed balanced with the actuator stroke tested prior to shipping.

3.0 out of 5 stars ( 2 )

$2,040.95

—

$2,995.00

FiTech Ultimate LS EFI 500 HP Fuel Injection Systems with Go Fuel In-Tank Module

FiTech Ultimate LS EFI 500 hp fuel injection systems with Go Fuel in-tank module combines incredible engineering and construction for top-of-the-line performance. FiTech fabricated many billet aluminum parts for their Ultimate LS EFI 500 hp systems, including a 92mm throttle body, high-volume fuel rails, and a 1,500 to 6,500 rpm powerband intake manifold. They combine sequential spark and fuel control with 36 lbs./hr. injectors, a plug-and-play wiring harness, and a color touch screen self-learning ECU. This allows for programing two fan control outputs, most tach and speedometer output drivers, and target AFR and timing on the fly. The Go Fuel in-tank module universal billet assembly can be used on tanks with a depth of 6 to 15 inches. The billet aluminum was designed with the supply and return ports in a parallel position to help route the fuel lines easily and evenly. The vent port is on the other side to ease routing the line near the fill tube. The two fuel ports are threaded to accept -6 AN O-ring boss fittings for a secure, leak-free connection. Whether you're starting with a 5.3 junkyard dog or a crate motor, FiTech Ultimate LS EFI 500 hp systems with Go Fuel in-tank module will look and run exceptionally. Additional Ultimate LS features: * Optional GM transmission control feature is suitable for 4L60, 4L65, 4L70, or 4L80 * Black anodized aluminum parts for style and corrosion resistance * High-flow, cable-operated throttle body * Bosch wideband-controlled * Stainless oxygen sensor bung * Compatible with car and truck coils * AN fittings and fuel crossover * Works with custom cams * Designed for applications making at least 6 in. of vacuum at idle * 24X and 58X crank and cam compatible * Programmable touch screen hand-held controller with data log features * Suction cup mounting bracket

5.0 out of 5 stars ( 1 )

$2,375.99

Holley Terminator X MAX Stealth 4150 24X LS EFI Fuel Injection Systems

Holley Terminator Max X Stealth 4150 24X LS EFI systems feature four 100 lbs./hr. fuel injectors capable of supporting up to 650 hp naturally aspirated or 600 hp on forced induction applications. The Terminator X ECU provides fuel maps that self-learn and integrated ignition timing control, yielding improved idle stability, drivability, and horsepower at wide-open throttle! Holley Terminator Max X Stealth 4150 24X LS EFI fuel injection systems also include transmission kick-down provisions for GM TH350/400, 200R4/700R4, and Ford C4/C6 applications, as well as plug-and-play transmission control for GM 4L60 and 4L80 applications. System features include: * All wiring exits below the fuel injector bowls for a complete stealth installation * Air entry machined to fit most stock-style air cleaners with air cleaner locator provisions * Integrated ignition timing control offers plug-and-play with factory LS coil sub-harness and OEM LS coils (no external boxes/modules needed to run coil near plug) * High-resolution, full-color touchscreen for initial setup, tuning, and gauge displays * Simple calibration wizard—no laptop required * (4) inputs (12 V, ground, 5 V, and frequency) for things such as additional pressure sensors, or activation triggers for nitrous activation, or a trans brake (fuel and oil pressure inputs are pre-terminated) * (4) Outputs (ground, PWM -) for accessories such as fans, boost control, nitrous control, IAC kit, and more * Genuine Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * OEM-style TPS/IAC for years of dependable service * Available in 3 finishes: shiny, black, and gold * Compatible with Holley EFI digital dashes, gauges, and fuel system accessories

Not Yet Reviewed

$2,819.95

Holley Terminator X Stealth 4150 24X LS EFI Fuel Injection Systems

Holley Terminator X Stealth 4150 24X LS EFI systems feature four 100 lbs./hr. fuel injectors capable of supporting up to 650 hp naturally aspirated or 600 hp on forced induction applications. The Terminator X ECU provides fuel maps that self-learn and integrated ignition timing control, yielding improved idle stability, drivability, and horsepower at wide-open throttle! Holley Terminator X Stealth 4150 24X LS EFI fuel injection systems also include transmission kick-down provisions for GM TH350/400, 200R4/700R4, and Ford C4/C6 applications. System features include: * All wiring exits below the fuel injector bowls for a complete stealth installation * Air entry machined to fit most stock-style air cleaners with air cleaner locator provisions * Integrated ignition timing control offers plug-and-play with factory LS coil sub-harness and OEM LS coils (no external boxes/modules needed to run coil near plug) * High-resolution, full-color touchscreen for initial setup, tuning, and gauge displays * Simple calibration wizard—no laptop required * Four inputs (12 V, ground, 5 V, and frequency) for things such as additional pressure sensors, or activation triggers for nitrous activation, or a trans brake (fuel and oil pressure inputs are pre-terminated) * Four outputs (ground, PWM -) for accessories such as fans, boost control, nitrous control, IAC kit, and more * Genuine Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * OEM-style TPS/IAC for years of dependable service * Available in three finishes: shiny, black, and gold * Compatible with Holley EFI digital dashes, gauges, and fuel system accessories

Not Yet Reviewed

$2,299.95

Holley Terminator X Stealth 4150 58X LS EFI Fuel Injection Systems

Holley Terminator X Stealth 4150 58X LS EFI systems feature four 100 lbs./hr. fuel injectors capable of supporting up to 650 hp naturally aspirated or 600 hp on forced induction applications. The Terminator X ECU provides fuel maps that self-learn and integrated ignition timing control, yielding improved idle stability, drivability, and horsepower at wide-open throttle! Holley Terminator X Stealth 4150 58X LS EFI fuel injection systems also include transmission kick-down provisions for GM TH350/400, 200R4/700R4, and Ford C4/C6 applications. System features include: * All wiring exits below the fuel injector bowls for a complete stealth installation * Air entry machined to fit most stock-style air cleaners with air cleaner locator provisions * Integrated ignition timing control offers plug-and-play with factory LS coil sub-harness and OEM LS coils (no external boxes/modules needed to run coil near plug) * High-resolution, full-color touchscreen for initial setup, tuning, and gauge displays * Simple calibration wizard—no laptop required * Four inputs (12 V, ground, 5 V, and frequency) for things such as additional pressure sensors, or activation triggers for nitrous activation, or a trans brake (fuel and oil pressure inputs are pre-terminated) * Four outputs (ground, PWM -) for accessories such as fans, boost control, nitrous control, IAC kit, and more * Genuine Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * OEM-style TPS/IAC for years of dependable service * Available in three finishes: shiny, black, and gold * Compatible with Holley EFI digital dashes, gauges, and fuel system accessories

Not Yet Reviewed

$2,299.95

Aeromotive VaporWorx Standalone KPM1500 Fuel Pump/Returnless Pulse Width Modulation Control Systems

Aeromotive VaporWorx KPM1500 fuel pump/returnless PWM control systems include a KPM1500 fuel pump modified with a high-pressure regulator, returnless pulse width modulation control system, and other modifications to make them work properly for most US-based vehicles. The KPM1500 features twin OEM Bosch PWM compatible pumps, fully re-engineered pump support system, robust venturi pump systems, integral safety overpressure valves, and a built-in anti-reversion/check valve, making each fuel pump very much like an OEM part. The outlet nipple has been strengthened to reduce the chances of breakage, and their operation is smooth, quiet, and easy to control. VaporWorx PWM (pulse width modulation) kit contains everything needed to drive the KPM1500 electrically in either constant/static or manifold referenced pressure modes. These kits are intended to be used as standalone control systems. No additional relays, Hobb's switches, etc. are needed. Features: * VaporWorx modified KPM1500 fuel pump module make the OEM chassis wiring plug-and-play * Approximately 71 percent+ reduction in power to the fuel pump during idle/cruise vs. running both pumps full speed all the time. Practically eliminates vapor lock/cavitation caused by overheated fuel * Fully returnless (external inline filter required) * 60-amp minimum continuous power rating in a compact controller package * Total size 4 in. L x 2.1 in. W x 1 5/8 in. H * Over-temperature shutdown with automatic reset operates indefinitely without damage * Short circuit protection that will operate indefinitely without damage * OEM Delphi/Aptiv connections for terminals, seals, and connector bodies (where appropriate)

Not Yet Reviewed

$2,917.70

Aeromotive VaporWorx KPM1500 Ally Returnless Pulse Width Modulation System Kits

Aeromotive VaporWorx Ally KPM1500 returnless PWM (pulse width modulation) system kits include a KPM1500 fuel pump modified with a high-pressure regulator, returnless Ally PWM control system, and other modifications to make them work properly for FSCM-equipped vehicles and aftermarket ECM/FSCM (fuel system control module) systems. The KPM1500 features twin Bosch PWM compatible OEM pumps, fully re-engineered pump support system, robust venturi pump systems, integral safety overpressure valves, and a built-in anti-reversion/check valve, making each fuel pump very much like an OEM part. The outlet nipple has been strengthened to reduce the chances of breakage, and their operation is smooth, quiet, and easy to control. The weakness of the OEM FSCM is power capability. They can drive one high-power pump, but not two. That's where the VaporWorx Ally PWM (pulse width modulation) kit comes in. It contains everything needed to drive the second KPM1500 electrically while the OEM fuel system control module handles the primary, keeping the power separated, but control of both pumps is handled by the FSCM, and all feedback, diagnostics, fuel pressure, etc. remains functional. These kits are intended to be used as an Ally, or piggyback, system to help the OEM FSCM. No additional relays, Hobb's switches, etc. are needed. Features: * VaporWorx modified KPM1500 fuel pump module make the OEM chassis wiring plug-and-play * Using PWM to slow down the pumps is very effective in keeping fuel temperatures down and relieving the electrical system of excessive load * Ally PWM controller is a unique control strategy that helps reduce the amount of power that the FSCM produces at higher fuel demand * At higher duty cycles the Ally PWM controller will start to out-run the FSCM and take more of the pumping power load, "helping out" the fuel system control module * Approximately 71 percent+ reduction in power to the fuel pump during idle/cruise vs. running both pumps full speed all the time. Practically eliminates vapor lock/cavitation caused by overheated fuel * Fully returnless (external inline filter required) * 60-amp minimum continuous power rating in a compact controller package * Total size 4 in. L x 2.1 in. W x 1 5/8 in. H * Over-temperature shutdown with automatic reset operates indefinitely without damage * Short circuit protection that will operate indefinitely without damage * OEM Delphi/Aptiv connections for terminals, seals, and connector bodies (where appropriate) * All cross-linked polyethylene wiring * UL94 rated components used throughout

Not Yet Reviewed

$2,917.70

FiTech Nitro-Port Cast LS3 1000 HP Fuel Injection Systems

FiTech Fuel Injection proudly introduces the Nitro-Port Cast LS3 1000 hp fuel injections systems, combining FiTech's cutting-edge EFI technology with the all-new Nitro-Port Series intake manifold. Designed for serious street builds and track performers, these complete EFI systems deliver reliable horsepower and modern drivability in one powerful package. At the heart of each kit is the Nitro-Port cast intake manifold, engineered with a low-profile modular runner design, short runners for high-rpm performance, -8 AN fuel rails, pre-drilled and tapped nitrous/water injection port, and support for 92mm, 102mm, and drive-by-wire throttle bodies (drive-by-throttle bodies coming soon). Rear-mounted vacuum ports and MAP sensor location keep installations clean and streamlined. Every Nitro-Port LS EFI System includes: * FiTech ECU * Complete wiring harness * Full set of sensors (including MAP, IAT, CTS, and more) * Dual Wideband O2 sensors * Touchscreen handheld controller for setup and tuning * And of course, the Nitro-Port intake manifold These plug-and-play systems take the guesswork out of EFI conversions while delivering exceptional performance and adjustability right out of the box. Whether you're swapping an LS into your muscle car or building a high-horsepower track weapon, the FiTech Nitro-Port LS EFI Systems provide the power, tuning control, and quality FiTech is known for.

Not Yet Reviewed

$2,245.00

—

$2,445.00