Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
Availability
51 Results Found For "Mustang Motor Mounts"
Showing In Stock Items. Show All 66 Items.
On Sale
Holley ECU Mounting Brackets
Holley ECU mounting brackets allow you to comfortably install either the Dominator ECU, Holley HP, Terminator X, or Terminator X-MAX under your Mustang's front passenger seat. They're designed to work with stock seats and seat tracks (modified/race seats may or may not accommodate them). You simply route all your ECU harnesses through the firewall--properly route the wires, install the unit followed by the ECU, and then reconnect your wires and go! Use your laptop to fine-tune the ECU without popping the hood and protect it from engine bay heat with Holley ECU mounting brackets. Order the brackets recommended for your application.
( 3 )
$112.95
$101.65
—
$105.95
DIYAutoTune MegaSquirt Gen 2 Plug-and-Play Engine Management Systems
DIYAutoTune MegaSquirt Gen 2 plug-and-play engine management systems are standalone units designed as direct-fit, factory ECU replacements offered for a variety of foreign and domestic vehicles. These powerful and cost-effective options typically require an hour or less for installation, and each includes a base map to get the motor fired up easily and ready for fine-tuning to match your engine's needs--from mild to wild. MegaSquirt Gen 2 ECUs get the job done with an impressive feature list that will let you do a lot more than you'd expect anywhere near this price point. DIY AutoTune MSPNP Gen 2 ECUs typically feature: * Fully plug-and-play installation--no wiring required for basic functionality * Base map is pre-loaded to help your engine start on the first turn of the key * Real-time tuning and data-logging with a laptop connection * Supports most aftermarket wideband sensors * 16 x 16 fuel tables allow high-resolution tuning * 12 x 12 ignition tables * Multiple acceleration enrichment strategies * Closed-loop idle speed control * Air conditioner control * Onboard peak and hold drivers support both high and low impedance injectors--no external ballast resistor is needed * Allows removal of stock airflow meter or stock MAF sensor, if so equipped * 12 x 12 air fuel ratio target tables for use with wideband oxygen sensor for precise tuning and table trim * Built-in 2-step rev limiter/launch control with flat shift * Real-time barometric correction * Internal 4-bar MAP sensor reads up to 44 psi of boost * Over-boost protection * Closed-loop boost control (requires boost solenoid kit) * Knock sensor input with adjustable sensitivity * Headphone output for knock sensor--listen for knock while you tune! * Table switching input--change fuel and spark maps on the fly for different fuels, nitrous activation, etc. * Input for flex fuel sensor--switch between E85 and gasoline on the fly! * CAN Bus connector allows interconnection of other MegaSquirt-compatible devices for additional functions, like: EGT input, automatic transmission controller, additional sensors ... the possibilities are limitless! * MegaSquirt Gen 2 plug-and-play ECU * MSPNP RS232 serial tuning cable, 6 ft. (USB adapter sold separately, if needed) * Tuning software and documentation USB stick * 6 ft. vacuum hose for MAP signal and "T" fitting * Four screws for ECU mounting
( 3 )
$869.99
Powermaster Mastertorque Starters
With their gear-reduction drives, heavy-duty PowerMaster Mastertorque starters really crank out the power--180 lb.-ft. of torque. So they can handle engines with compression ratios as high as 14.0:1. If your stock starter clears your oil pan, they will, too. Some will also clear kicked-out pans. A selection of Mastertorque starters can be mounted in multiple orientations, and some will work inverted with the solenoid down. They feature a black wrinkle finish and select models are available in a chrome plated finish.
( 629 )
$186.99
—
$197.99
Optima RedTop Starting 12-Volt Batteries
Optima RedTop Starting 12-volt batteries are the ultimate power source for cars, trucks, SUVs, hot rods, and other high-performance vehicles. They're engineered with unique Spiralcell technology, delivering a stronger burst of ignition power, while extending the battery life up to three times longer than conventional models. Maintenance-free RedTop AGM batteries are sealed, leak-proof, and resistant to vibrations—so you can mount them anywhere and in virtually any position on your vehicle. Order the Optima battery designed for your application, and expect a perfect start every time.
( 1533 )
$279.99
—
$309.99
Ford Performance Parts Distributor Hold-Down Clamps
Have you ever wished you could replace that rusty old distributor hold-down clamp? Well now you can with these great looking Ford Performance Parts hold-down clamps. Available for a variety of Ford engines, the clamps, and their included bolts, are made of heavy-duty steel and triple chrome plated for great looks and corrosion protection. We can't think of a better way to dress up your engine and keep your timing accurate.
( 23 )
$11.99
CVR Protorque Maximum Starters
CVR Protorque Maximum starters with 3.1 hp and a 4.44:1 gear reduction ratio are sure to get your engine cranking with ease. They feature a unique aluminum housing to eliminate hot start problems and are adjustable (where applicable) to help clear suspension parts, oil pans, and exhaust systems. Protorque Maximum starters are sealed units with rubber O-rings and grommets and also have easily replaceable plungers and contacts.
( 22 )
$283.99
—
$341.99
On Sale
Mr. Gasket Distributor Hold-Down Clamps
Since you're installing that new distributor, you'll need to hold it down with something. Why not use one of Mr. Gasket's hold-down distributor clamps? Made from heavy gauge steel, these clamps are the perfect way to dress up the engine compartment.
( 28 )
$15.61
Meziere True Start 400 Series High-Torque Starters
These Meziere True Start 400 series high-torque starters are recommended for all high-compression, large displacement engines up to 700 cubic inches and supercharged applications. They feature custom gear reduction for the best cranking power and rotational speed. Their innovative billet aluminum head design provides the strongest drive gear support without an external nose support. The starter block features a full 360 degrees of clocking positions in 10 degree increments. Meziere True Start 400 Series high-torque starters feature an offset design that clears all kickout style oil pans.
( 17 )
$679.06
Summit Bucks
Denso Oxygen Sensors
Oxygen sensors, also known as Lambda sensors or O2 sensors, are among the most sensitive and critical components on your car's engine. They monitor the air/fuel mixture under idle, moderate acceleration, and cruise conditions. Oxygen sensors have a smaller range of limits in detecting and adjusting the difference from an optimum air/fuel ratio than the newer wide range air/fuel sensors (A/F sensors). Today's engines may use as many as four oxygen sensors to monitor exhaust gas oxygen content and catalytic converter efficiency. In order to perform these functions properly, Denso oxygen sensors adhere to strict OE standards within incredibly close tolerances. A malfunctioning or incorrectly calibrated oxygen sensor can hurt drivability and illuminate the check engine light, resulting in costly and time-consuming repairs. Denso First Time Fit oxygen sensors are designed to meet those tolerances and more. Key features and benefits of Denso Oxygen Sensors include: * Robotic laser welds * Porous PTFE filters block efficiency-robbing contaminants * Double-protection covers maintain proper temperature for quicker response times and protect ceramic elements from silicone and lead fouling * Rugged, watertight stainless steel housings resist corrosion and contamination * Aluminum oxide trap layers keep silicone and lead out, preventing damage to the platinum electrode * Refined zirconia elements improves sensor response * Superior design maximizes engine performance while reducing fuel consumption and harmful emissions * First Time Fit design delivers the right part the first time
( 96 )
$29.99
—
$50.99
CVR Protorque Starters
With 1.9 hp and a 4:1 gear reduction ratio, these CVR Protorque starters are sure to get your engine cranking. These starters feature a unique aluminum housing to eliminate hot start problems and are adjustable (where applicable) to help clear suspension parts, oil pans, and exhaust systems. These CVR Protorque starters are sealed units with rubber O-rings and grommets and also have easily replaceable plungers and contacts.
( 162 )
$234.99
—
$276.99
Powermaster PowerMax Starters
With their gear-reduction drives, heavy-duty Powermaster PowerMax starters really crank out the power--180 lb.-ft. of torque. So, they can handle engines with moderate compression ratios. If your stock starter clears your oil pan, the Powermaster PowerMax starters will, too. Some will also clear kicked-out pans. Powermaster PowerMax starters can be mounted in multiple orientations to fit your needs. Starter dyno reports are included.
( 1162 )
$147.99
—
$202.99
Powermaster XS Torque Starters
Powermaster's highly efficient XS Torque starters feature extra-powerful motors that churn out up to 200 lbs.-ft. of torque. Coupled with their 4.4:1 gear-reduction ratio, that equals reliable cranking power for engines, up to a whopping 18.0:1 compression ratio. These starters come with a billet adapter/mounting block for durability. They'll also clear your oil pan if the OE starter did. Some models are available in a chrome plated finish. Starter dyno test results are included. Order the replacement designed for your vehicle application.
( 912 )
$219.99
—
$373.99
Four Seasons Replacement Electrical Switches
Four Seasons replacement electrical switches are engineered and tested to provide years of trouble-free operation. They offer a large selection of switches for vehicle specific applications to maintain and service HVAC systems. Four Seasons replacement electrical switches are zinc coated to resist corrosion.
( 7 )
$58.99
On Sale
MSD Pro-Billet Ready-to-Run Distributors
MSD Pro-Billet Ready-to-Run distributors are the perfect upgrade for weak OE electronic distributors, outdated points distributors, and large HEIs or DuraSparks. All that's required is to install the distributor in the engine, and connect three wires and the coil! A maintenance-free magnetic pickup accurately triggers this ignition with increased output from the amplifier, easily outperforming stock ignitions. It will smooth out the engine's idle, improve starting, and perform at a much higher rpm. The housing is machined from billet 6061-T6 aluminum, using state-of-the-art CNC mills and lathes for a unit with no porosity or weak areas. For stability and endurance, an oversized steel shaft spins in a top-mounted sealed ball bearing, while an extra-long sintered bushing guides the shaft at the base of the housing. This shaft also receives a QPQ coating for low friction wear and resistance against corrosion from humidity and ozone buildup. The distributors feature MSD's adjustable mechanical advance, which allows you to custom-tailor an ignition curve to match your engine's needs. Most models are also available with a vacuum advance canister to help improve economy. Order the model recommended for your vehicle and engine application.
( 332 )
$849.95
$571.95
—
$767.95
Summit Racing™ Protorque Starters
Summit Racing™ Protorque Starters are 100 percent new! Our lightweight Nippondenso-type starters offer a 4.0:1 gear-reduction ratio and a whopping 1.9 HP. That's 222 ft.-lbs of racecar cranking power. If that's not enough cranking power to suit you, there are even more powerful 3.1 hp monsters, which are a pound lighter! They have a 4.44:1 reduction ratio and churn out an awesome 342 ft.-lbs. of torque. Both of our Summit Racing™ powerhouses are suitable for engines up to 502 c.i.d., and compression ratios of up to 18.0:1. GM versions are adjustable for five mounting positions; Ford types, for 18. And, to prevent corrosion and electrical shorts, both starters wear a gold dichromate finish.
( 605 )
$235.99
—
$315.99
Powermaster Ultra Torque Starters
Powermaster Ultra Torque starters live up to their name by delivering 250+ ft.-lbs. of torque. They feature a machined aluminum adjustable mounting block, work with most oversized kickout oil pans, and work great for big cubic inch engines. The starters use a 2.5 kW, in a 3.4 hp motor.
( 247 )
$275.99
—
$403.99
Tilton Severe-Duty Super Starters
Tilton severe-duty Super Starters pack a lot of power into a compact package--a hefty 3.0 hp, in fact. That's enough to crank over just about anything, and they only weigh about 12 lbs. They feature full ball-bearing or needle-bearing construction that's little affected by heat or cold, and most are "clockable" for multiple choices of solenoid positioning. These starters are recommended for engines over 400 c.i.d., as well as high-compression V8s.
( 35 )
$480.25
On Sale
MSD DynaForce Starters
MSD DynaForce starters are built with all-new components and hand-assembled in the USA. For maximum performance and reliability, all starters are dyno-tested and blueprinted before they leave the factory. The armature is balanced during assembly and is guided by two ball bearings for smooth engagement during thousands of starts. MSD DynaForce starters feature a 3.4 hp motor—and a reduced 4.4:1 gear ratio delivers superior torque to start high-compression race engines up to an 18:1 ratio. They include a downsized housing that clears most headers and oil pans, and a billet aluminum mounting block that can be clocked in different positions for tighter clearance applications. These starters are available in a durable red or black powdercoat finish that's designed for maximum protection while looking good. They use a nickel plated, heavy-duty solenoid for optimum performance in severe environments. Order the model designed for fitment with your vehicle application.
( 242 )
$488.95
$439.95
Powermaster Street Alternators
Powermaster street alternators feature all of the quality construction and dependability the company is famous for. The "electrical generators" are available in a variety of amperages and styles, allowing you to choose the best model for your specific ride and the accessories you run. So whether you need an alternator for your truck, hot rod, musclecar, sport compact, or audio competition vehicle, Powermaster gives you the power you need to get it started and keep it going.
( 1827 )
$213.99
—
$345.99
On Sale
Holley Sniper EFI HyperSpark Distributor Kits
Holley Sniper EFI HyperSpark distributor kits were designed to make upgrading your ignition on a Sniper EFI-equipped engine simple. When installed concurrently with a new Sniper EFI system, the combination creates the easiest way to install EFI conversion on the market—and only four flying lead connections are required! The harness only requires one connection to a switched power source, battery positive, battery negative, and fuel pump power. The pre-terminated connectors and a built in 40A relay provides power to all of the components within the system. With the included Sniper EFI main harness you no longer need to run multiple wires to provide switched power for each individual component, which not only helps prevent wiring confusion, but it will also speed up your install time and clean up your engine bay. Simply route the harness and pre-terminated connectors to your HyperSpark coil, distributor, and ignition box and plug them in. Available for all popular engine combinations, these kits come with a distributor, coil, ignition box, and an integrated Sniper EFI harness. Order the application you need. Key features: * Plug-and-Play Sniper EFI main harness replaces the standard Sniper EFI harness with four loose leads, battery positive, battery ground, switched 12 V, and fuel pump power, for a simple and streamline installation * Designed for existing or new Sniper EFI installations (the HyperSpark Master Kit harness retains the same flying lead wire colors as the Sniper EFI main harness; new installations will not use the Sniper EFI standard harness or coil driver * Complete ignition system in a box, including: HyperSpark ignition box, HyperSpark ignition coil, HyperSpark distributor (for your application), and a plug-and-play main harness * HyperSpark distributors feature a Hall Effect crank trigger sensor providing a noise-free rpm signal to the Sniper ECU * Patented clear installation cap eliminates any confusion while installing the distributor * HyperSpark CD ignition box is seal and powder coated to be installed in the harshest of locations * External LED on HyperSpark CD Ignition box helps verify 12 V, cranking rpm, and low battery voltage * 135mJ of spark energy when used with the HyperSpark ignition coil, ensures complete combustion * Integrated ignition coil bracket simplifies mounting the Ignition coil * Ignition coil connector removes any doubt of loose connections at the Ignition coil * Enables timing control on a Sniper EFI Installation
( 23 )
$1,024.95
$921.95
On Sale
MSD Pro-Billet Ready-to-Run EFI Distributors
MSD Pro-Billet Ready-to-Run EFI distributors are the perfect upgrade when you start making serious power with your EFI Ford or Chevy. They use a stock-style trigger pickup and come with plug-in connectors. Installation is simple by removing the stock distributor, then plugging in and bolting the new one in place! A maintenance-free magnetic pickup accurately triggers this ignition with increased output from the amplifier, easily outperforming stock ignitions. These distributors will smooth out the engine's idle, improve starting, and perform at a much higher rpm. Their housings are machined from billet aluminum, using state-of-the-art CNC mills and lathes. For stability and endurance, an oversized steel shaft spins in a top-mounted sealed ball bearing for accuracy through the entire rpm range. Chevy models also feature an extra-long sintered bushing at the bottom and an extra oil tract machined into the bottom of the housing for improved lubrication. The tract delivers oil directly to the cam and distributor gears. All of the shafts receive a QPQ coating for low friction wear, and resistance against corrosion from humidity and ozone buildup. The Chevrolet models have also been tested by the Underwriter's Laboratory, and are certified to meet or exceed safety standards for marine ignition systems as set by the U.S. Coast Guard.
( 93 )
$538.95
—
$649.95
$484.95
—
$583.95
Powermaster Ultra Torque High-Speed Starters
Powermaster Ultra Torque high-speed starters deliver 25 percent more cranking rpm at the flywheel than the standard Ultra Torque starters. They are perfect for use in blown alcohol engines, or any engine requiring higher than normal cranking speed. The Powermaster Ultra Torque high-speed starters feature a 2.2 kW, 3.0 hp motor and have a machined aluminum adjustable mounting block. They will fit all oversized and kickout-style oil pans with no clearance problems.
( 30 )
$347.99
—
$372.99
CVR Protorque Ultra Starters
CVR Protorque Ultra starters live up to their name by delivering 250+ lb.-ft. of torque. They feature a specially wound field coil and armature to deliver that torque throughout the cranking range. The machined aluminum adjustable mounting block works with most oversized kickout oil pans, and are great for big cubic inch engines. The starters use a 2.5 kW, 3.4 hp motor that'll support up to 18:1 compression ratio.
( 15 )
$222.99
—
$273.99
On Sale
Holley Sniper HyperSpark Ready to Run Small Cap Distributors
Holley Sniper HyperSpark ready to run small cap distributors adds plug and play ignition timing control to any Holley EFI system. This line of distributors comes with a built-in ignition coil driver, removing the need of mounting an ignition box or external coil driver. The design includes a single Hall Effect sensor providing engine rpm to the ECU. The precision shutter wheel design ensures accurate timing, even at very high engine speeds. They can also be used with other EFI systems that support a Hall Effect crank signal input. Order the model designed for your application needs. Features: * Easiest plug-and-play way to add timing control to any Sniper EFI installation * Designed to work with HyperSpark ignition coil (PN: 556-152); also compatible with most canister ignition coils using the supplied ring terminals * Built-in ignition coil driver, safely provides enough spark energy for applications up to 450 hp * Patented clear installation cap eliminates any confusion while installing the distributor * Cast aluminum distributor housing looks right at home in nearly every engine bay * Comes with cast gear installed—contact camshaft manufacturer for recommended gear material * Comes with steel gear for SBF applications with an aftermarket camshaft * Precision shutter wheel provides the ECU a clean rpm signal via a single Hall Effect sensor, ensuring accurate timing even at high engine rpm * Shutter wheel design allows for a "timed sequential" fueling strategy with Terminator X, HP, and Dominator ECU's * Includes wire retainer for a clean installation
( 2 )
$562.95
