Availability
Showing In Stock Items. Show All 409 Items.
Tremec offers a variety of TKX 5-speed manual transmission for select GM and Ford applications. Each model features different gear ratios. Order the transmission best suited for your vehicle. General product details: * Bolts up to a standard GM Muncie bellhousing or use a Quicktime bellhousing * Input Shaft: 26-Spline (requires 26-spline clutch disk) * Output Shaft: 31 Spline * The TKX has 600 lbs.-ft. of torque capacity and is capable of engines speeds of 8,000 rpm with shifts at 7,500 rpm. It is available in multiple gear ratio configurations. * Designed for multiple applications with three shifter locations. Compact, end-loaded design provides clearance in most transmission tunnels without floor * Increased case strength with 3-piece aluminum housing provides outstanding structural stiffness (includes main case, intermediate plate and rear extension). Gaskets at all flanges simplifies installation and eliminates fluid * Superior shift-ability through use of multi-cone synchronizers and hybrid synchronizer rings made of sintered bronze and carbon * Noise, vibration and harshness (NVH) minimized with gear layout to best control stress All gears supported by caged needle bearings to reduce end play on the gears. * All gears and shafts made from special grade steel (ASTM 4615), providing increased torque carrying * Equipped with a high performance short-throw billet aluminum shifter that isolates road noise, while providing clean, crisp * Robust design with internal 3-rail shift system and steel shift * Wide gear width increases gear life and torque * Built-in reverse light switch and cruise control safety
( 44 )
$2,999.99
Summit Racing™ Automatic Transmissions combine quality and economy to offer replacement transmissions in many styles and options. These units are remanufactured with all-new clutches, thrust washers, seals, bushings, and high-energy bands, along with other "failure prone" hard parts depending on unit. Other features include a rebuilt front pump, a valve body with shift for street and performance and high-quality seals and gaskets. You get all these impressive upgrades, along with reliable performance and extreme value. All transmissions are Dyno tested before they're shipped. Order the model recommended for your vehicle.
( 59 )
$2,090.99
—
$5,455.99
Summit Bucks
BluePrint Engines 350 c.i.d. Cruiser crate engines make an excellent choice for daily drivers and cruising. These crate engines make up to 18 inches of vacuum and are designed to work with power brakes, stock torque converter, stock gearing--and run great on 87 octane fuel. Get a new engine and bring your ride to life with BluePrint Engines Cruiser crate engines.! More features, products, and specifications include: * 341 hp / 371 lbs.-ft. torque * Compression ratio: 9.2:1 * Aluminum heads * Hydraulic roller cam * Cast iron crankshaft * Hypereutectic pistons Block: * New BluePrint cast iron block * 4-bolt main * 4.000 in. bore * One-piece rear main seal * Mechanical fuel pump provision * Passenger side dipstick * Drilled and tapped for clutch linkage Rotating assembly: * Cast iron crankshaft * 3.480 in. stroke * Forged 5.700 in. connecting rods * Hypereutectic pistons * Internal front/external rear engine balance Cylinder heads: * BluePrint aluminum cylinder heads (H8002K) * 64cc chamber * 2.020 in. intake / 1.600 in. exhaust valves * 195cc intake / 75cc exhaust runners Roller cam specifications: * 0.477 intake / 0.471 exhaust * 202 intake / 212 exhaust duration @ 0.050 in. 115-degree LSA (Lobe Separation Angle) Ignition timing: * 32 degrees total at 3,500 rpm Also includes: * Valve covers * Oil pan * Timing cover * Dyno tested results shipped with engine
( 9 )
$4,899.00
The Edelbrock Power Package concept is second to none. To make things easier in parts selection, Edelbrock has taken the guesswork out of top-end component selection by actually placing the power package components together in complete kits. They include almost everything you need to make serious horsepower. These kits are available with different cams, intakes, and heads to deliver the torque and horsepower you're looking for. Horsepower output will vary depending on combinations of accessories used.
( 11 )
$2,389.95
Awesome performance and awesome looks combine with these ATK High Performance GM 350 390 hp Stage 1 long block crate engines. They are topped with trick looking parts and they have the power to back them up. These engines are hand-assembled and balanced to help them put out 390 hp and 420 ft.-lbs. of torque that will tear up the street or strip. Whether you are looking to pack some more power in your street rod, muscle car, or truck, ATK has you covered. ATK GM 350 390 hp Stage 1 long block crate engines include: * Handpicked, remanufactured block * ATK High Performance aluminum cylinder heads with 2.020 in. /1.600 ex. valves * OE crankshaft and connecting rods * Hypereutectic pistons * Hydraulic roller camshaft * Valve covers * Timing cover and timing set * Oil pan, pump, and pickup tube
( 15 )
$3,798.99
ATK High Performance GM 350 345 hp/400 lbs.-ft. Stage 1 long block crate engines are classics with great street manners, and vacuum to power all your accessories. These Stage 1 or base engines are designed for those that may have their own component parts already, and who also are interested in completing out the build themselves. Typically ATK GM 350 345 hp base long block engines consist of: * Seasoned OE short block with 4-bolt mains * OE cast crankshaft * OE 5.7 in. powder metal connecting rods * Hypereutectic pistons * Moly piston rings * Hydraulic roller camshaft * 220/224 at .050 in. * .495 in./502 in. lift 110 LSA * ATK cast iron cylinder heads * 76cc combustion chambers * 165cc intake runners * 1.94 in./1.5 in. valves * Stamped steel 1.5 ratio rocker arms * Valve covers * Timing set and cover * Oil pan, high volume oil pump with pick-up tube
( 12 )
$3,198.99
Edelbrock Pro-Flo 4 EFI systems provide you with a high performance traditional-style intake and 4150-style throttle body. Unlike regular throttle body EFI systems, Pro-Flo 4 features the fuel rails and individual injectors for each cylinder mounted on the manifold. This Edelbrock design produces the best fuel atomization and distribution for the ultimate performance, as well as delivering the most control and the most efficient way to deliver fuel to your engine. Along with innovative design, Pro-Flo 4 systems have the latest technology with an all-new ECU, and even more features for advanced tuning, with the key being their exclusive E-Tuner app with base calibrations developed on their dyno. Edelbrock Pro-Flo 4 EFI systems include and feature: * Engine Control Unit with faster processor and upgraded Bluetooth chip in a thinner waterproof design * Fully assembled intake manifold with air valve, fuel rails, and injectors * Fully assembled OEM high-quality wiring harness with pre-terminated connectors and labeled connection for a simplified installation * E-Tuner application for setup and engine monitoring * Wideband oxygen sensor * Distributor (not included with LS kits) * Gaskets and hardware * Installation instructions * Ready to run out of the box with pre-loaded calibrations * Self-learning technology--no tuning experience or laptop tuning required * Ignition control--adjust ignition curve with the E-Tuner 4 App for optimal performance and mpg * Offered with multiple fuel injector choices * Now boost compatible up to 15 psi by switching to a 2-bar MAP sensor and downloading the new firmware update from Edelbrock for free! It is recommended to regularly check for firmware updates even if not utilizing boost control. * Systems automatically compensate for altitude and weather changes * E-Tuner 4 app with Bluetooth connectivity between ECU and Android phone or tablet. Includes multiple dash display configurations for monitoring engine vitals and performance; multiple control functions including two adjustable cooling fan outputs, idle speed, AFR set points, acceleration fuel tuning, ignition control, cold start fuel, and cranking fuel.
( 125 )
$2,375.95
—
$2,534.95
Build your project exactly how you want with QA1 Level 2 Big Wheel kits! Get the perfect look by easily adjusting your ride height with front and rear coilovers. Raise or lower your car 2 in. the front. Raise it up to 2 in. or lower it by up to 3 in. in the rear. QA1 Level 2 Big Wheel kits allow you to dial-in the exact style you want in minutes with the included spanner wrench. These complete bolt-on suspension kits are designed to fit up to 28 in. wheels on your vehicle and include everything needed to get your Box sitting right, while giving you a better ride and improved handling. Product features and benefits: * Double-adjustable coilovers give you the ability to individually tune your shock compression and rebound to get the perfect ride and get more grip off the line for drag racing * Adjustable upper and lower trailing arms allow your wheel and tire package to fit with adjustable trailing arms that center your rear axle in the wheel well to gain more clearance for up to 28 in. wheels * Tubular control arms are much lighter and stronger than stock and will upgrade front-end geometry for better drivability—and are designed specifically for big wheel cars with corrected suspension angles for large wheels and tires * Tubular sway bars help reduce body roll and improve stability with front and rear sway bars to reduce handling issues that come from big wheels and raised ride heights * Easy, bolt-in installation * Parts come powdercoated and ready-to-install with all necessary hardware to allow you to bolt up the kit right in your garage or work with your local shop * Works with original factory rear axle housings or Quick Performance 9 in. rear axle housings
( 2 )
$5,255.95
—
$5,439.95
Edelbrock E-Force supercharger kits use a positive displacement supercharger that is capable of producing over 500 hp. These kits include the supercharger with Eaton internals, a manifold, drive pulleys, a belt, and all necessary items for installation. Edelbrock E-Force superchargers are designed to provide more horsepower per pound of boost than their competitors, from off-idle through the rest of the rpm range. Plus, their internal bypass valve practically eliminates parasitic loss, consuming less than 1/3 of one horsepower at 60 mph. NOTE: They are not compatible with HEI distributors.
( 8 )
$3,644.95
—
$3,730.95
Give your car or truck a little more punch with one of these ATK High Performance GM 350 Vortec 350 hp Stage 2 long block crate engines. These engines are built from the ground up to replace your old, tired mill with a more modern, efficient engine. ATK hand-builds and balances each one these engines to ensure they are great-running, reliable engines that will get you back on the road. Engine specifications: * HP: 350 * TQ: 400 * Block: OE roller block 4-bolt main 1-pc seal 1996-2000 * Bore/Stroke: 4.040 in. x 3.480 in. * Displacement: 350CI * Crankshaft: OE reground external balance rear of crank/internal balance front of the crank * Rods: OE powder metal 5.7 in. * Pistons: Hypereutectic 9.5:1 compression * Rings: Moly * Camshaft: Hyd. Roller * Cam Specs: 220/224 @50 .495in/.502ex 110LSA * Timing Chain: Double roller * Cylinder Heads: Vortec cast iron 67cc 1.94/1.50 *Rocker Arms: Stamped steel 1.5 ratio * Oil Pan: Rear sump 5qt (not for Chevelles with steering behind crossmember, some Corvettes and 62-67 Chevy II's) * Oil Pump: Melling STD volume * Balancer: Internally balanced – PowerBond #PB1046-N * Flexplate: Externally balanced – Pioneer #FRA-159 * Intake Manifold: ATK HP dual plane * Distributor: HEI (Iron Gear) * Water Pump: OE long pump Recommended components: * Carburetor: Quick Fuel 680CFM vacuum secondary's electric choke #HR-680 * Fuel Pump: Holley mechanical 110GPH #12-327-11 * Spark Plugs: Autolite #605 * Spark Plug Wires: 8mm Engine Info: * Oil: Conventional/Non-Synthetic 10W30 * Oil Filter: Wix or K&N * Timing: 34-36 Degrees * Spark Plug Gap: .035 in. * Firing Order: 18436572 * Octane: 91+ * Stall Converter: Stock * Exhaust: 1 5/8 Headers
( 8 )
$3,688.99
On Sale
Holley Sniper 2 EFI Inline Pump Fuel Injection Systems are self-tuning, easy-to-install, EFI conversions for 4-barrel (4150 flange) style carburetors. They took everything that they learned from the original Sniper EFI system and added new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple user interfaces/dash displays, and more. New for Sniper 2 is the Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12 V source is all that's required to power the PDM and your Sniper EFI. Make your classic drive like a modern fuel-injected vehicle, with easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley's comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine—and the system will begin self-tuning with no laptop or tuning required. If you're looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI. Main features: * Only 4 wiring connections required: Battery+, Battery-, Switched Ignition, and RPM * Includes 20 feet of 3/8 in. vapor guard fuel hose, filters for before and after the pump, fittings and hardware, cushioned mounting brackets, and an external, inline pump * Can be used with 3/8 in. factory sending units or add a dedicated bulkhead fitting * Innovative clamping system allows you to locate the module anywhere in the tank beside your existing sending unit and can be rotated 360 degrees for easier clocking. * Main harness includes plug-and-play HyperSpark distributor support for integrated timing control, making your ignition setup hassle-free * Wide variety of tuning and gauge display options: from a 3.5 in. full-color LCD hand-held, 5 in. digital dash, or the Bluetooth dongle, which allows you to connect either an iOS or Android based cell phone to your Sniper 2 * Female -6 AN O-ring fittings * Overall height is only 3.280 in. * Supports up to 650 hp naturally aspirated or 575 hp on boost with four 100 lbs.-hr. injectors * Requires 55-65 PSI * Next generation ECU features improved RF noise and interference resistance (stands up to old car wiring, noisy alternators, faulty plug wires) * Redesigned throttle shaft and plate geometry for a smoother throttle feel * Integrated transmission kickdown provisions for GM TH350/400, 200-4R/700R4 and Ford C4/C6 applications * "Hidden Harness" wiring exit from the rear of throttle body for a clean appearance * Inputs and outputs consist of: 2x ground inputs, 2x ground outputs, 1x TPS output (0-5 V), and 1x tach output * Redesigned injector connector for improved reliability * Onboard contactless magnetic TPS sensor ensures an accurate TPS reading * Next generation mil-spec style M8 positive lock connector for CAN1 and CAN2 provides the latest in CAN bus technology for a simple yet robust connection * Cast-in fuel crossover from the primary to secondary fuel rail * The included Bosch LSU 4.9 wideband oxygen sensor provides real-time fuel map learning * Included clamp-on oxygen sensor kit ensures a leak-free oxygen sensor install with stainless steel T-bolt clamps and a stainless steel weldable oxygen sensor flange * Sniper 2 throttle bodies are serialized, which provides an improved experience in the event of any unit needing to be inspected
( 17 )
$2,349.95
—
$2,549.95
$2,113.95
—
$2,293.95
Give your ride new life with ATK High Performance GM 350 330 hp/380 lbs.-ft. Stage 1 long block crate engines. These engines are based on the tried-and-true small block Chevy and are built to perform right out of the box. ATK hand-assembles and balances each engine using top-quality parts to help them produce awesome power. Whether you are replacing an older, worn down engine or just looking for a little more performance, ATK has you covered. Stage 1 long block crate engines include: * Handpicked, remanufactured blocks * ATK cast iron cylinder heads * 76cc chambers * 165cc intake runners * 1.94 in./1.5 in. valves * Stamped steel 1.5 ratio rocker arms * OE crankshaft * OE 5.7 in. powder metal connecting rods * Hypereutectic flat-top pistons * Moly rings * Hydraulic flat tappet camshaft * 465 int./.488 exh. cam lift * 224 int./234 exh. cam duration at 0.50 * 9.1:1 compression * Valve covers * Timing cover and timing set * Oil pan, pump, and pickup tube
( 16 )
$3,099.99
Give your old ride new life with these ATK High Performance GM 350 345 hp/400 lbs.-ft. Stage 3 long block crate engines. These engines are built to perform and look great without breaking your budget. Each engine is expertly assembled, balanced, blueprinted, and topped with quality components, making it a solid, reliable mill to power your muscle car, street rod, or pickup. ATK GM 350 345 hp Stage 3 long block crate engines include: * Handpicked, OE remanufactured block * ATK cast iron 75cc/165cc 1.94/1.50 heads * ATK dual plane intake manifold * Quick Fuel 680 cfm vacuum secondary carburetor * OE crankshaft * OE 5.7 in. powder metal connecting rods * Hypereutectic pistons * Hydraulic roller camshaft .495in/.502ex 110LSA * HEI Distributor, plug wires and plugs * Holley 110 GPH mechanical fuel pump * Valve covers * Timing cover and double roller timing set * 5 qt. oil pan, high volume oil pump with pickup tube * OE style long water pump * PowerBond 8 in. balancer and 168 tooth flexplate
( 1 )
$4,504.99
Billet Specialties Tru Trac serpentine systems with A/C feature easy, straightforward assembly—with no spacers or washers to fool with. The entire Tru Trac systems are designed to mount to the engine block to allow for any cylinder head/intake configuration. All hardware and fasteners are included in each kit to complete the install. Tru Trac serpentine systems with A/C include: * Powermaster 170 amp 1-wire alternator * Billet aluminum alternator fan and pulley * Edelbrock water pump * Billet aluminum water pump pulley * Billet aluminum bridge bracket * Patent-pending billet aluminum tensioner engineered specifically for each Tru Trac serpentine system * Billet aluminum tensioner pulley * Billet aluminum crankshaft pulley * Polished ARP 12-point stainless steel fasteners * Goodyear Gatorback 6-rib serpentine belt * Comprehensive installation manual * Polished Sanden SD-7 A/C compressor * Polished billet aluminum A/C compressor clutch cover * Polished billet aluminum A/C compressor manifold
( 20 )
$2,499.95
Summit Racing™ SPC Engine Blocks are aftermarket V8 Engine Blocks made for "Street, Performance, or Competition." These new clean sheet designed aftermarket blocks are cast in a modern state-of-the-art German foundry on brand new molds and machined in USA on modern high-speed machining centers that can hold the tightest of tolerances. Why start your engine build with a dirty, old, worn-out production block that needs hundreds or thousands of dollars of machine work--when you can start with a new heavy-duty casting full of high-performance features. We ship these blocks mostly finished but leave the cylinder bore .005" undersize, your machine shop will have to hone them for proper size. You can rest assured that you have a great foundation for your engine build. Check out the features below! Additional details: • Available Versions Include: GM Small Block, GM LS, GM Big Block (coming Soon,) Ford Windsor 5.0 and 351W • Cast in Germany at a Tier 1 OEM foundry • Made with class 35 Iron Alloy, Higher tensile strength and harder than competitors' class 30 • Machine-finished in USA on precision hi-speed machining centers- All dimensions are very accurate! • Priority main oiling systems & Siamese Cylinder bores • Blind head bolt holes • 4-bolt main caps, 180,00 PSI main bolts included
( 11 )
$2,249.99
—
$2,299.99
TCI StreetFighter transmissions are durable enough to withstand the rigors of even the toughest street machines. Equipped with a manual/automatic valve body, most units allow you to manually shift the vehicle into each gear change or, by placing it in the drive position, remain fully automatic. In either mode, you get a race track shift that bangs through the gears and shaves time off of your ETs. When you use the manual gear selection feature, the StreetFighters upshift and downshift right when you move the lever, with no lag or governor override. When you select the normal drive position, they retain positive automatic shifts for the ease of driving you look for in an automatic transmission.
( 144 )
$2,064.95
—
$4,996.95
On Sale
Silver Sport EasyFit transmission kits are designed to be the perfect start to your TREMEC TKX installation. The kits are tailored with a vehicle-specific shifter position and components to make your installation easy and less costly. Features and specs: * STX Shifter--short throw shifter (depending on kit) * Transmission mount, reverse light harness, pilot bushing, and required hardware * 5-speed pattern shifter ball or 5-speed shift pattern console plate (depending on kit) * EDP coated, steel crossmember (depending on kit) * Gear ratios--2.87, 1.89, 1.28, 1.00, 0.68, 2.56R * 600 lb.-ft. torque rating * 26-spline count input shaft * Quality-tested with a 12-month factory warranty
( 4 )
$4,095.00
—
$4,395.00
$3,890.25
—
$4,175.25
Dart SHP Special High Performance small block Chevy cast iron bare blocks are designed for high performance and heavy duty applications. These SPH blocks are an ideal starting point for hot rodders, drag racers, circle track competitors, off-roaders and high performance marine enthusiasts. Key features of SHP small block Chevy bare blocks are: * Priority main oiling system * Siamese cylinder bores with extra-thick walls * Extra thick decks to ensure reliable head gasket seal * Blind head bolt holes (don't go through water jacket) * Scalloped water jacket walls for improved flow around cylinders for better cooling * Clearance for 3.75 in. stroke with steel rods * Splayed outer bolts on middle main bearing caps * Provisions for OE stock roller lifters and cams * All OE bolt holes starter, clutch ball, etc. * Uses 1981 to 1985 stock style oil pan and passenger side dipstick * Uses stocked stamped steel or plastic timing cover
( 21 )
$2,299.99
On Sale
Race-ready AFR 220cc SBC Eliminator racing heads feature 100 percent CNC-ported intakes with greater detail. They also come with 100 percent CNC-ported combustion chambers and 80cc exhaust ports with a 3/4 in. thick head deck (ideal for nitrous or blower applications). Standard valves are lightweight 8mm, 2.080 in. intakes and 1.600 in. exhausts with AFR's hardened ductile iron interlocking valve seats. The valve springs included are intended for use on roller camshafts. They also offer exceptional flow characteristics, a 23 degree valve angle, and standard valve spacing. These cylinder heads are perfect for 350 to 400 c.i.d. engines in bracket drag cars, sportsman oval trackers, and highly modified street-class cars operating between 3,000 and 7,500 rpm (higher rpm ranges are possible, depending on the combination of parts).
( 22 )
$2,592.45
—
$3,279.15
Wilwood forged narrow Superlite 6R Big Brake front brake kits upgrade your late model ride with increased brake capacity and complimentary style. They're application-specific for a simpler installation and offer full compatibility with OE master cylinder output and ABS functions, where used. These front brake kits feature the extremely durable and efficient body design of their forged narrow 6-piston radial mount calipers. You can choose from optional caliper finishes and rotor designs to meet your personal style and braking requirements. Don't just replace—upgrade to generate big stopping power with Wilwood forged narrow Superlite 6R Big Brake front brake kits.
( 101 )
$2,141.96
—
$2,857.65
AFR 195cc SBC Eliminator Street Heads are fully CNC-machined (combustion chamber, intake, and exhaust ports) and available in your choice of straight or angled plug versions. AFR 195cc heads feature a 75cc or 65cc combustion chamber with a 64cc exhaust port and a 3/4 in. thick head deck (ideal for nitrous or blower applications). Standard valves are lightweight 8mm, 2.050 in. intakes (competition versions are 2.080 in.) and 1.600 in. exhausts with AFR's hardened ductile iron interlocking valve seats. The valve springs included are intended for use on roller camshafts. The exceptional flow characteristics of AFR 195cc Eliminators, a 23 degree valve angle, and standard valve spacing make them the perfect street heads for 350 to 400 c.i.d. engines in the 2,000 to 6,500 rpm operating range. They carry CARB #D-250-2 when used on 1969-94 applications with the heat riser. Order the bare or assembled model recommended for your vehicle and engine.
( 40 )
$2,328.90
On Sale
B&M remanufactured Street and Strip transmissions are put together with new gaskets, bushings, seals, thrust washers, high performance friction materials, and gold zinc plated hardware. The front pump is rebuilt to B&M specs and the valve body is recalibrated. They're built for extreme conditions and are perfect replacing a worn transmission, cruising, and racing.
( 13 )
$3,749.95
—
$4,049.95
$3,373.95
—
$3,643.95
Eagle competition rotating assemblies consist of name-brand quality components for a wide range of engines at an affordable price. Depending upon your selection, these kits may feature a crankshaft, pistons, piston rings, rod and main bearings, or connecting rods. Balanced assemblies are also available. Order the model designed for fitment on your year/make vehicle and engine application.
( 33 )
$2,836.99
—
$2,867.99
ATK High Performance GM 383 Stroker 415 hp Stage 2 long block crate engines are the perfect choice to drop in your ride if you're looking for some stroker power without breaking the bank. They are made of high-quality name brand parts at an affordable price and are perfect for getting your ride back on the road. ATK long block crate engines include: * Intake manifold * ATK High Performance aluminum cylinder heads with 2.020 in. /1.600 ex. valves * Distributor * Oil pan * Valve covers * Timing cover * Water pump * Harmonic balancer
( 5 )
$4,898.99
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
