Availability
Showing In Stock Items. Show All 10 Items.
Street Master torque converters are designed for the driver who is looking for a competitive advantage. By raising the stall rpm, these converters will completely eliminate slow, sluggish starts. Recommended for stock to slightly modified engines for maximum performance, they'll allow the engine to idle smoothly when the car is in gear. All stall speeds are approximate ratings for fresh big block engines. Small blocks will vary 300 to 500 r.p.m. lower.
( 232 )
$852.99
—
$1,313.99
Tow Master series torque converters from Hughes Performance are designed to increase bottom-end pulling power in your tow vehicle without sacrificing top-end efficiency or lockup. Because they offer your vehicle more power with less effort, mileage can be increased by as much as 1-2 miles per gallon. Recommended for slightly modified engines, these Tow Master converters help you get the job done. All stall speeds are approximate ratings for fresh big block engines. Small blocks will vary 300 to 500 rpm lower.
( 25 )
$865.99
—
$891.99
Street Rod torque converters from Hughes Performance are designed and manufactured for street rod enthusiasts needing a bit of an upgrade over their OE stock converters. These converters feature silicon brazing for strength, needle bearings for reliability, and stator modifications for more torque multiplication. All stall speeds are approximate ratings for fresh big block engines. Small blocks will vary 300 to 500 rpm lower.
( 113 )
$869.99
—
$895.99
Hughes Performance Fuel Miser torque converters reduce the slippage in your transmission by 25 percent. The result is better fuel economy, more efficient shifts, and cooler transmission temperatures. They are designed to work with engines over 400 c.i.d. as well as with diesel applications. All stall speeds are approximate ratings for fresh big block engines. Small blocks will vary 300 to 500 rpm lower.
( 19 )
$891.99
Ford Performance Parts driveshaft assemblies feature reduced overall weight and rotating mass that frees up horsepower and provides quicker acceleration, higher speeds, and lower ETs. They feature heavy-duty, 6061 aluminum, seamless drawn tubing and include high-strength U-joints or flange yokes. Available for a wide variety of Mustang applications, they are designed for increased horsepower applications to deliver exceptional strength and reliability. Depending on application, features include: * 1330 or stronger 1350 high performance U-joints * 28-spline or 31-spline yokes * 3.5 in. diameter * 0.114 in. or 0.125 in. wall thickness * Spline and slip design allows for installation and suspension movement * Hard plastic boot to keep grease in and water out; protects spline and slip from contaminants * Eliminates the need for a center support bearing * Direct bolt-in * Fully assembled and balanced
( 18 )
$491.99
Centerforce TRIAD XDS clutch kits supply triple disc clutches developed for vehicles requiring a holding capacity of 500 to 1,200 ft.-lbs. of torque at the crank. For superior clamp load the billet pressure plates feature their patented centrifugal weight system (where applicable), while the patented ball bearing-actuated pressure plate (where applicable) provides light pedal effort. TRIAD XDS disc packs are equipped with metallic friction material for increased holding capacity and they are available in either sprung or solid hub styles, depending on application. The clutches are equipped with lightened billet steel flywheels providing low inertia, resulting in quicker rpms. Centerforce TRIAD XDS clutch kits may feature: * No complicated setup or adjustments * 8.75 in. diameter designed to lower inertia for heavy track use * Centrifugally assisted diaphragm to increase holding capacity with rpm * Solid hub design offers light weight and quick shifts * Patented multi-disc floating disc and drive disc designs * Holds 500 to 1,200 ft.-lbs. of torque at the flywheel * Patented ball bearing pressure plate * Specification card * Excellent driver control * Positive drive floater * Precision-balanced * ARP fasteners
Not Yet Reviewed
$2,309.95
Want to get back the power and gas mileage that you lost from installing those big tires on your Jeep? Motive Gear makes it easy to re-gear your 4x4 with their ring and pinion gear and installation kit combos. These complete kit combos include front and rear ring and pinion sets, plus front and rear bearing kits, giving you everything you need to re-gear the front and rear differentials in one package. The kits come in a wide range of ratios for most Dana applications. Their quality is the result of years of development, outstanding design, and state-of-the-art manufacturing methods to ensure a perfect fit for an easy install.
( 8 )
$1,454.98
—
$1,882.98
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
