Availability
Add GM 6L80/90E transmission control to any existing vehicle utilizing a Terminator X Max ECU. A departure from traditional Holley EFI transmission control, the Terminator X Max ECU allows the ability to use 2007+ GM 6L80E and 6L90E transmissions by communicating via CAN with the internal TCM (Transmission Control Module). The supplied Holley EFI OBDII transmission tuning hand-held is used to adjust shift points, tire size and gear ratio. Terminator X V3 software provides the ability to dial in torque management to optimize the desired shifting characteristics when using a 6L80/90E transmission. The software also enables you to control the secondary shift mode within the transmission TCM and allows use of tap Up/Down shifting. Within Terminator X V3 PC Software: --- Virtual Torque Management Tables --- Virtual TPS Tables to dial in shift characteristics regardless of engine --- DBW and Timing torque reduction tables to create smooth shifts Within the Holley EFI OBDII Transmission Tuning Hand-held: --- Ability to read and clear TCM fault codes --- Ability to raise and lower shift points by MPH or RPM --- Support for Tap Up/Tap Down & Transmission's Secondary Shift Mode If you currently have a Terminator X ECU, upgrading to a Terminator X Max ECU can be easily done by plugging your main harness into the Max ECU and re uploading your existing calibration. Holley Terminator X MAX GM 6L80/90 transmission kit features: * Included TCM hand-held tuner with integrated wizard is required for setup in conjunction with the Terminator X 3.5 in. hand-held. Terminator X V3 software unlocks optional tuning parameters. * Plug-and-play with any engine controlled by a Terminator X Max ECU * Supports: Shift Mode - Tap Up / Tap Down, and torque management * Four loose wires: --- Power (Red): Supplies power to the transmission solenoids. This should be connected directly to the battery, or a constant battery source capable of supplying 5 amps --- Ground (Black): Connect to a good chassis/engine ground source --- Brake Switch (Light Blue/White): Wired to the brake light switch. This must be installed to a +12 V source (as most brake light switches are) --- Park/Neutral Safety (Yellow): Circuit for starter solenoid. When the transmission is in Park or Neutral, this yellow wire will be grounded (-). When the transmission is in gear this circuit will be open.
Not Yet Reviewed
$573.95
A faulty transmission control module can leave you stranded in a hurry—but ACDelco has a direct replacement for your vehicle application. Each module has been thoroughly tested to offer the same function and performance as the OEM parte. Restore smooth shifting with a new transmission control module from ACDelco.
( 1 )
$122.99
—
$332.99
Clearance
ACDelco GM Genuine Parts transmission control modules are GM-recommended replacements for your vehicle's original components. They manage the operation of your vehicle's automatic transmission, and they contain the module and solenoid valves all in one unit. These original equipment transmission control modules have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.
( 1 )
$115.99
$115.50
Pacific Performance Engineering heavy-duty PTO side cover plates are designed to add strength to the center of the transmission case and eliminate transmission oil seepage at the mating surface. They are manufactured from durable cast aluminum, and feature cooling fins double the surface area (60.74 sq. in.) when compared to stock (30.62 sq. in.). Thereby increasing heat dissipation from the transmission oil. The plates include mounting hardware and gaskets to complete the installation.
( 2 )
$80.99
Chevrolet Performance offers transmission control modules for a wide range of vehicles—including many Chevy and GM Allison transmission and Duramax diesel engine applications from 2009 and up. These Genuine GM pre-programmed TCMs can solve problems such as erratic shifting patterns, loss of communication to transmission control module, inhibited shift range, and more. The brand new plug-and-play direct fit replacements are constructed from high-quality materials and factory specifications to maintain stock fit and performance.
( 2 )
$530.99
Edelbrock TC transmission controllers are offered as a standalone system to work with Pro Flo 4, most aftermarket fuel injection systems and carbureted applications utilizing a TPS sensor. Features: * Transmission control over shift points, firmness, speed, torque converter lock up, shift table, speedometer calibration and line pressure * Edelbrock TC Tuner calibration app (available for both Android and Apple devices) and optional 7 in. touchscreen Bluetooth tablet for setup, adjustment and visual display * Easy install with compact housing and clean-look wiring harness * Includes base calibrations for a plug-and-play setup * Compatible with carbureted applications utilizing a standalone throttle position sensor * CAN bus communication for functionality with all Pro-Flo 4 systems and most aftermarket EFI systems * Also, allows you to change the final drive ratio, tire diameter, and transfer case ratio
( 3 )
$864.95
—
$910.95
Previously offered in the guise of a standalone crate engine, the Godzilla is now offered as a complete package—thanks to the Ford Performance 7.3L Power Module with 10R140 automatic transmission combo kits. They are a complete powertrain solution, utilizing the 7.3L V8 Ford gasoline crate engine from the 2020 F-250 Super Duty and 10R140 automatic transmission (2WD). The Godzilla crate engine features aluminum cylinder heads, iron for the block, forged steel for the crankshaft, a 10.5:1 compression ratio, and port fuel injection. For this application, the 7.3-liter colossus develops 430 horsepower at 5,500 revolutions per minute and up to 475 lbs.-ft. (644 Nm) of torque at 4,000 revolutions per minute. The control pack bundles the powertrain control module with Ford Performance-specific calibration, an electronic throttle pedal, a Mustang Bullitt airbox, an 87-millimeter throttle body, and an adapter. The FEAD kit includes a handful of accessory drive bits. Other list of components include a starter, an alternator and a bracket, the power steering pump, tensioner, and belt. In addition to the Super Duty-spec 10R140 automatic transmission, Ford Performance also includes transmission cooler, shifter, and cable assembly, as well as all necessary mounting hardware. Kit includes: M-6007-73 Super Duty crate engine: * 7.3L displacement * 430 HP at 5,500 rpm * 475 lbs.-ft. of torque at 4,000 rpm * 10.5:1 compression * Port fuel injection M-6017-73A control pack: * PCM with Ford Performance calibration * Electronic throttle pedal * Mustang Bullitt airbox * 87mm Bullitt throttle body with adaptor M-8600-73 FEAD kit: * Alternator and bracket * Power steering pump * Tensioner * Belt * Installation hardware Production Super Duty 10R140 transmission and torque converter: * Transmission cooler * Shifter cable assembly (no shifter) * Mounting hardware * Starter and index plate
Not Yet Reviewed
$18,999.99
Ford Performance Parts has the complete solution for your drivetrain upgrade needs with the 5.0L Coyote manual power module and T-56 manual transmission combo kit, which includes: * Gen 4X 5.0L Coyote crate engine * Tremec 6-speed manual transmission * Complete engine controller and wiring harness (control pack) It's Next Generation 5.0L power all in one complete powertrain kit. The crew at Ford Performance have spec'd out a kit to simplify the swap of the newest, most innovative 5.0L Coyote engine into just about any Ford vehicle. The Coyote power module teams the Gen 4X 5.0L Coyote V8 with a state-of-the-art Tremec 6-speed transmission, plus all the electronics and hardware to finish the installation. The engine features direct and port fuel injection, twin independent variable camshaft timing, and a lightweight plasma transferred wire arc spray aluminum engine block. Coyote power modules simplify both the shopping and build experience by kitting up the right parts that are matched to deliver potent performance with civilized drivability. The engine control pack is truly plug-and-play and simplifies conversions to a modern electronically fuel injected V8 high performance engine. Details and/or specs: * Gen 4X 5.0L Coyote engine * 460 hp at 7,000 rpm * 420 lbs.-ft. torque at 4,600 rpm * 12.0:1 compression ratio * Aluminum block * Boss 302 alternator kit * Starter and starter index plate * Control pack PCM and installation kit is tunable for power upgrades * Runs on pump gas * Steel Quicktime bellhousing * Roller pilot bearing * Tremec 6-speed transmission 2.66 1st gear * Clutch fork / throw-out bearing * Clutch kit * Billet flywheel * Installation hardware * Note: Engine will be fitted with an automatic flexplate. Included is a billet flywheel, to be installed on engine before installation into vehicle.
Not Yet Reviewed
$19,699.99
Ford Performance presents the next generation 5.0L power all-in-one complete powertrain kit! The crew at Ford Performance spec'd out these kits to simplify the swap of the newest, most innovative 5.0L Coyote engine into just about any Ford vehicle. The Coyote power module teams the Mustang GT 460 hp 5.0L Coyote V8 with a state-of-the-art 10-speed automatic transmission, along with all the electronics and hardware to finish the installation. The engine features advances like direct and port fuel injection, twin independent variable camshaft timing, along with a lightweight plasma transferred wire arc spray aluminum engine block. The Coyote power module simplifies both the shopping and build experience by kitting up the right parts that are matched to deliver potent performance with civilized drivability. The engine control pack is truly plug-and-play to simplify the conversion to a modern electronically fuel injected V8 high performance engine. Build the Coyote project of your dreams with high-quality aftermarket parts by Ford Performance!
Not Yet Reviewed
$19,555.99
The FAST TCU 2.0 is fully programmable with the included T-Com 2.0 laptop software and features Dual Tune Technology, so you can create and easily switch between two completely different shift modes—daily driving or performance. These controllers allow the ability to make infinite adjustments to shift points and line pressure for maximum performance from automatic electronic transmissions, and are paddle/button shifter compatible. Designed to be compact with LED diagnostics and data logging functions, the FAST 2.0 is also compatible with FAST EZ-EFI 2.0 and XFI Fuel Injection Systems, through the CAN/BUS connection, and can be configured to read engine sensors and transmit data to other modules and displays. Twelve outputs allow for precise, closed loop current control and programming of non-transmission control functions, such as engine shutdown after a specified idle duration. For advanced programming and more versatility, choose FAST TCU 2.0 controllers!
Not Yet Reviewed
$1,102.95
These Chevrolet Performance automatic transmission controllers include the wiring harness, controller, software, and laptop hookup. They are designed to allow for the use of electronically controlled transmissions in early model vehicles. Chevrolet Performance automatic transmission controllers are fully programmable for upshift, downshift, part throttle and wide-open shifts, and shift firmness. They come preprogrammed--just enter your rear tire diameter and rear axle ratio and go, or create your own custom shift characteristics. Chevrolet Performance automatic transmission controllers were originally developed by GM Racing for off-road truck racing. They have the ability to record and graph drag racing data like time, speed, shift point, engine rpm, and more.
( 1 )
$1,224.68
Mopar Replacement transmission control modules are among the best and longest-lasting electrical system parts available. They'll deliver the fit, form, and function you expect. Keep your vehicle electronics working efficiently with the replacement transmission control module designed for your application.
Not Yet Reviewed
$146.99
—
$916.99
Take the complexity out of wiring your Gen 4X 5.0L Coyote crate engine with a Ford Performance Parts control pack. Ford Performance Parts 2021-23 Coyote 5.0L control packs are available to run the crate engine with a Mustang 10R80 automatic transmission or a manual transmission. Choose the control pack needed for your build. Control packs feature: * PCM with unique Ford Performance calibration * Electronic throttle pedal eliminating cable routing issues * Unique harness replaces the stock body harness and is designed for custom vehicle installation * OBD-II port for trouble-shooting/code reading * Power distribution module, air box, air inlet tube, upper and lower radiator hoses, and HEGO sensors are included * Requires return-type fuel system
( 1 )
$2,462.99
FiTech presents Ultimate LS standalone ECUs. These self-learning ECUs are offered with and without transmission control. So if you're considering utilizing a factory intake, throttle body, and injectors, FiTech Ultimate LS standalone ECUs will get your engine ready for optimal performance.
( 50 )
$567.00
—
$1,202.00
Ford Performance Parts 2018-20 Gen 3 Coyote control packs are designed to run 2018-20 5.0L Mustang GT Coyote (Gen 3) automatic transmission engines with 10R80 Mustang GT 10-speed transmissions. They include a unique control pack harness, which replaces the stock body harness. These Ford Performance control packs were designed for performance enthusiasts who want the Gen 3 Coyote package in their own custom build. Includes: * PCM with Ford Performance calibration (requires return-type fuel system; not compatible with return-less-type) * Electronic throttle control accelerator pedal, eliminating throttle cable routing problems * OBD-II diagnostic port to assist in vehicle calibration upload and problem diagnosis * Power distribution module * Mustang GT air box * Mustang GT air inlet tube * MAF sensor * Upper and lower radiator hoses * HEGO sensors
Not Yet Reviewed
$2,201.99
Ready for standalone engine management at a budget price? Take control of your GM Gen V LT1, L83, or L86 engine with a Holley Terminator X Max GM Gen V LT direct injection kit! They're available to fit early non-WT drive-by-wire engines, as well as late WT drive-by-wire engines. Terminator X and X Max features and benefits: * Plug-and-play GM Gen V LT engine control, including GDI and VVT support * Ideal for swapping late model GM Gen V LT engines into vintage vehicles * 3.5 in. hand-held gets your engine running in no time with a step-by-step calibration wizard * GM LS and LT drive-by wire throttle body control (Terminator X Max only) * GM 4L60 and 4L80 transmission control (Terminator X Max only) * Included engine harness plugs directly into the factory LT DI injector sub harness * OEM Injectors supported, with part numbers provided in the handheld wizard or software * Genuine Bosch LSU 4.9 wideband control (will not work with LSU 4.2 oxygen sensors) * On-Board Diagnostic LEDS for: ECU Power – Engine Run – Wideband Status – TPS Calibration – Crank Signal – Cam Signal – VVT Status – Pump Control – and DI Injectors. This allows you to identify any critical engine issues at a glance * Built-in 1 bar MAP sensor, vacuum hose adapters included (1/8th, 1/4 and 3/16ths); or for Boosted applications, you can disable the internal MAP sensor, and utilize an external LT MAP sensor. The harness comes with the connector terminated, making the installation a snap * 4 inputs: 12 V, Ground, 5 V, and Frequency—for things such as additional pressure sensors, or activation triggers for nitrous activation, or a trans brake (Fuel and Oil Pressure inputs are pre-terminated) * 4 Outputs: -- Ground -- PWM – for accessories such as fans, boost control, nitrous control, IAC kit, and more -- Boost Control – Boost vs Time, Boost vs Gear, Boost vs RPM, Boost vs Speed, Boost Safeties -- Nitrous Control – Single Channel of Wet or Dry, Progressive or Non-Progressive, Rich/Lean Safeties, and target Closed Loop AFR * Integrated data logging to the 3.5 in. hand-held SD card * Free EFI tuning software for complete control of your Terminator X powerplant Terminator X Max ECU Connections: * J1A - Main Harness Connector: This connector is primarily an "Input" connector. It contains all the sensor inputs and wide band oxygen sensor control. * J1B - Main Harness Connector: The second connector is the "J1B" connector (26 pin). This connector is the "output" connector. It has eight injector outputs and outputs for other devices. * MAP Sensor: Used on N/A applications, connect directly to full manifold vacuum port on the intake manifold. * Main Power: Connects to the Main Power Harness; these two wires MUST be wired directly to the battery terminals. * J3: Connection point for the drive-by-wire harness. * J4: Connection point for the transmission harness.
Not Yet Reviewed
$3,049.95
—
$3,549.95
FiTech Ultimate TPI standalone ECUs bring an old GM TPI-controlled engine (L98, LB9) into modern times. These standalone EFI kits plug into all existing sensors on a GM TPI engine and provides complete control of the engine. From timing control to self-learning fueling, FiTech Ultimate TPI standalone ECUs deliver new life into the GM TPI engine.
( 9 )
$954.00
—
$1,060.00
Ford Performance Parts 2018 Coyote 5.0L control packs take the complexity and mystery out of wiring the engine. These engine management systems include a powertrain control module (PCM) with Ford Performance calibration, as well as an electronic throttle control accelerator pedal (which eliminates throttle cable routing problems). A unique control pack harness replaces the stock body harness and is designed for custom vehicle builds. It features an OBD-II diagnostic port to assist in vehicle calibration upload and problem diagnosis. Mustang Coyote 5.0L control packs include a power distribution module, air box, air inlet tube, MAF sensor, upper and lower radiator hoses, and HEGO sensors. Additional notes: * PCM with Ford Performance calibration requires a return-type fuel system; it will not work with a return-less fuel system * Supercharged versions, modified engines, and modified applications require custom calibration * Installation of this PCM in a 2018 Mustang GT will result in a no-start condition * For 2011-14 engines, use control pack M-6017-A504VA * For 2015-17 manual transmission version control pack, use M-6017-504V * For 2015-17 automatic transmission version control pack, use M-6107-M50A
( 2 )
$2,266.99
HalTech Nexus R3 with universal wire-in harness kits are ideal for dedicated race cars, engine swaps and custom wiring jobs. The harness has a set of VCU connectors at one end and unterminated wires at the other. All the wires at the unterminated end are color-coded and clearly labeled. Connect your HalTech VCU to the terminated end and follow your wiring diagram for all the engine connections. Load your base map and you're ready to go! * Color-coded and labeled wires that match the detailed wiring diagram for a confusion free construction process. * The wiring diagram is accompanied by the full VCU manual and software located on the USB key provided with the VCU, or downloadable from the HalTech website. VCU OVERVIEW: * Nexus R3 combines the functionality of a power distribution module, a data logger, a wideband controller, and a state-of-the art engine management system in one powerful device HalTech calls a VCU (Vehicle Control Unit) * 4 x 25A (continuous) push-pull PWM capable (5 kHz) outputs (for power to injectors / coils, transbrake, thermofan, fuel pump) * 8 x peak/hold injector drivers (can be used as low side drive outputs) * 8 x low current ignition outputs (can be used as low side drive outputs) * 6 x low side drive outputs, PWM capable (DPOs) * 6 x push-pull /H-bridge outputs (8A, PWM capable), e.g. for electronic throttle * 11 x 0-5 V analog inputs with redundancy for electronic throttle and switchable 5 V pullup * Trigger and home inputs with differential inputs, adjustable thresholds and glitch filters * 6 x synchronous pulsed inputs, zero crossing or adjustable thresholds - cam sensor inputs, frequency inputs or 0-5 V analog inputs * 1 x on-board wideband controller, supporting NTK and LSU4.9 * 1 x on-board 4 bar MAP sensor * 2 x CAN ports with switchable termination * Suits: Engines with up to 8 cylinders or up to 4 rotors. Racing applications where advanced race features, data logging and power management control are required. * Includes: Nexus R3 VCU, SurLok connectors (red and black), WiFi antenna, mounting bolts, USB-C cable, USB-C dust cap, USB drive with NSP software. Nexus R3 universal wire-in engine harness.
Not Yet Reviewed
$2,799.00
Take the complexity and mystery out of wiring your late model, 2018-2023 5.0L Mustang Coyote engine with the Ford Performance Coyote 5.0L control packs! These engine management systems are designed to run Ford Performance 5.0L Mustang Coyote engines. 2018-2023 Coyote 5.0L control packs features: * Includes PCM with Ford Performance calibration * Includes electronic throttle control accelerator pedal which eliminates throttle cable routing problems * Unique control pack harness replaces stock body harness and is designed for custom vehicle builds * Features OBD-II diagnostic port to assist in vehicle calibration upload and problem diagnosis * Includes power distribution module, air box, air inlet tube, MAF sensor, upper and lower radiator hoses and HEGO sensors * PCM with Ford Performance calibration requires return type fuel system, will not work with returnless fuel system * Supercharged versions, modified engines, and modified applications require custom calibration Note: Not for use with 2018+ F-150 Engines. Installation of this PCM in a 2018+ Mustang GT will result in a no-start condition.
Not Yet Reviewed
$2,394.99
Painless Performance OEM computers feature a stock calibration made for your specific vehicle while removing the VATS (vehicle anti-theft system) making them the perfect solution for your engine swap. Some tuning may be required for your specific application, but the computer will allow you to start your vehicle and get it to a local tuner. Make your engine swap easier with Painless Performance computers.
( 8 )
$199.99
Get ready to "Push the Boundaries" with HP Tuners CORE standalone engine control units! Created and designed for gearheads and craftsmen who need the utmost level of customization, CORE ECUs deliver superior control over your powerplant with many features that go beyond the constraints of factory ECUs. They provide all the necessary sensor interfaces, ignition drivers, injection drivers, and output drive stages required for total engine control. Bringing the CORE ECU to life is HP Tuners' VCM Live software, combining the diagnostics and calibration elements into a single, user-friendly interface. HP Tuners CORE ECUs are designed for all levels of LS swaps and high-performance motorsports builds. Currently CORE supports Gen 3 and Gen 4 LS engines with a 24x crank and 1x cam trigger along with 58x crank and 4x cam triggers. Drag, circuit, off-road racing; drifting, rally, or restomods, no matter what your high performance application, HP Tuners CORE ECU will provide everything you need for total control, performance, and ease of use. Order yours today. Key features: * Up to 16 injector control (fuel) and 8 coil packs (spark) * Sequential injection * Flex Fuel support * Dual throttle body capability * Two built-in Lambda controllers * Internal datalogging--up to 150 channels at 1kHz * 3 CAN bus networks (2 CAN and 1 HPT net) and ethernet connectivity * Turbo boost and anti-lag control * Single-stage On/Off and progressive nitrous control * Launch control * Map switching * A/C control, alternator control, etc.
Not Yet Reviewed
$1,999.99
Ford Performance Parts 7.3L gas engine control packs include components and harness to install a 2020 to present Super Duty 7.3L gas engine with a 10R140 automatic transmission in a vehicle. The unique control pack harnesses replace the production body harness designed for custom vehicle builds. These kits require use of a conventional return-type fuel system. Note: Installation of PCM in a production vehicle will result in a "no start" situation.
Not Yet Reviewed
$2,285.99
—
$2,396.99
Shifnoid Outlaw bump boxes allow for a smooth transition during the dragstrip staging process. These trans-brake controllers are critical to cars that need to rev up before final staging (such as turbo cars), but are also used by many non-turbo bracket racers. The ability to slide through the pre-stage beams and into the staged beams with precise tuning cuts down on rocking, bumping, and red light starts. These boxes are easy to use. Simple adjustments can be made to accommodate different tracks, power levels, and rpms. One-touch operation results in better focus, consistent launching, and improved reaction times.
( 1 )
$207.99
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
