Availability
Holley Sniper EFI HyperSpark distributor kits were designed to make upgrading your ignition on a Sniper EFI-equipped engine simple. When installed concurrently with a new Sniper EFI system, the combination creates the easiest way to install EFI conversion on the market—and only four flying lead connections are required! The harness only requires one connection to a switched power source, battery positive, battery negative, and fuel pump power. The pre-terminated connectors and a built in 40A relay provides power to all of the components within the system. With the included Sniper EFI main harness you no longer need to run multiple wires to provide switched power for each individual component, which not only helps prevent wiring confusion, but it will also speed up your install time and clean up your engine bay. Simply route the harness and pre-terminated connectors to your HyperSpark coil, distributor, and ignition box and plug them in. Available for all popular engine combinations, these kits come with a distributor, coil, ignition box, and an integrated Sniper EFI harness. Order the application you need. Key features: * Plug-and-Play Sniper EFI main harness replaces the standard Sniper EFI harness with four loose leads, battery positive, battery ground, switched 12 V, and fuel pump power, for a simple and streamline installation * Designed for existing or new Sniper EFI installations (the HyperSpark Master Kit harness retains the same flying lead wire colors as the Sniper EFI main harness; new installations will not use the Sniper EFI standard harness or coil driver * Complete ignition system in a box, including: HyperSpark ignition box, HyperSpark ignition coil, HyperSpark distributor (for your application), and a plug-and-play main harness * HyperSpark distributors feature a Hall Effect crank trigger sensor providing a noise-free rpm signal to the Sniper ECU * Patented clear installation cap eliminates any confusion while installing the distributor * HyperSpark CD ignition box is seal and powder coated to be installed in the harshest of locations * External LED on HyperSpark CD Ignition box helps verify 12 V, cranking rpm, and low battery voltage * 135mJ of spark energy when used with the HyperSpark ignition coil, ensures complete combustion * Integrated ignition coil bracket simplifies mounting the Ignition coil * Ignition coil connector removes any doubt of loose connections at the Ignition coil * Enables timing control on a Sniper EFI Installation
( 21 )
$999.95
Holley Terminator X engine control modules are standalone units intended for use as service components for your Terminator X EFI installation. Each ECU features real-time fuel learn, high-impedance injector drivers, an integrated 1 Bar MAP sensor, and four programmable inputs and outputs. The inputs and outputs are ideal for electric fans, boost control solenoids, or progressive nitrous control. Order your Holley EFI Terminator X Service ECU today. Features: * Compatible with Terminator X harnesses * OEM (Original Equipment Manufacturer) injectors supported with part numbers provided in the handheld wizard or software * Bosch LSU 4.9 wideband control (will not work with LSU 4.2 oxygen sensors) * Eight built-in multi-color diagnostic LEDs allow you to quickly identify a variety of potential system issues, such as: -- A failed TPS (Throttle Position Sensor) Autoset -- Faulty crank or cam sensors -- Potential oxygen sensor issues * Built-in 1 Bar MAP (Manifold Air Pressure) sensor -- On boosted applications, you can disable the internal MAP sensor and utilize an external MAP sensor * Four inputs—12 V, Ground, 5 V, and Frequency for things, such as: -- Additional pressure sensors -- Activation triggers for nitrous activation -- A trans-brake (Fuel and Oil Pressure Inputs are pre-terminated) * Four outputs--Ground, PWM, and accessories such as: -- Fans, boost control, nitrous control, IAC kit, and more * Boost control: -- Boost vs. Time/Gear/RPM/Speed, and boost safeties * Nitrous control: -- Single channel of wet or dry -- Progressive or non-progressive -- Rich/lean safeties -- Target closed loop AFR * Advanced tables: -- Four 1D tables -- One 1D per gear table -- Four 2D tables -- One 2D per gear table * Free EFI tuning software for complete control of your Terminator X powerplant
Not Yet Reviewed
$849.95
Holley EFI Smart Coils are a bolt-in ignition upgrade for your late model HEMI or Coyote engine. Here's the difference over a stock coil: they produce more spark energy while consuming less power without sacrificing voltage output. This means you get hotter spark at the plug to burn the maximum amount of fuel in each cylinder while using less power from your electrical system. Smart Coils are available individually or in sets of 8. * For Coyote or Hemi combinations currently using Holley EFI or Terminator X, use Smart Coil Ignition Harnesses 558-312 and Coil Extension Harnesses 558-326 for a plug-and-play solution. * For new Holley EFI installations on Coyote engines, use with Holley EFI Coyote TI-VCT Main Harness for Smart Coils 558-122 and Smart Coil Ignition Harness 558-312 for a plug-and-play solution. Features: * Direct bolt-on to factory valve covers * Same wiring pinout as other IGN-1A coils for easy plug-in upgrades (Will not work with factory wiring) * More spark energy than any other smart coil on the market for maximum fuel burn during combustion sequence * Low current draw means less demand on the electrical and charging system * Built-in ignitor for compatibility with Holley EFI and many other aftermarket ECUs * Maximum operating voltage of 18 V—for compatibility with both 12 V and 16 V electrical systems found in many performance/race applications
Not Yet Reviewed
$799.95
Holley EFI 8-Channel CAN EGT (Exhaust Gas Temperature) controllers are designed exclusively for use with Holley's 8-Channel EGT monitoring kit to measure both exhaust gas and cylinder head temperature. Knowing the exhaust gas temps of each cylinder in your engine may not only help you find potential horsepower that you've left on the table, but also pinpoint weak links your engine may have—allowing you to perform fuel adjustment at the cylinder level. Features include: * 8-Channel CAN EGT module * Plug-and-play for a quick and easy installation * EGT module main harness (4 ft.) * Compatible with Holley HP and Dominator ECU * Requires EGT probes (sold separately) * Requires V5 Build 100 or newer software/firmware
( 1 )
$876.95
Choose EFI main power wiring harnesses from Holley to meet your needs. Several choices are offered—TBI, LS applications, multi-point, and un-terminated harnesses—to feed and carry your engine's electrical supply. Get wired for electronic fuel injection with Holley EFI systems main wiring harnesses.
Not Yet Reviewed
$949.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
