Availability
Engine Works offers lightweight fuel pump pushrods for a variety of applications, including many Chevy small block and big block engines from the 1950s and up. They feature a tubular design with one hardened steel end and one bronze end for use on all aftermarket camshafts. Aluminum rods with brass tips are also available. Select from models designed for use with cast iron or billet steel roller cams.
Not Yet Reviewed
$24.96
—
$29.96
High-tensile strength head bolt kits are a necessity with any performance engine build and Engine Works offers a broad selection of head bolt kits to help you complete your cylinder head installation. These head bolt kits contain strong, high-quality steel bolts with a high-tensile strength much higher than OE bolts. Order the bolt kit designed for your application needs.
Not Yet Reviewed
$44.96
—
$49.96
Engine Works offers billet timing pointers for a variety of applications, including many Chevrolet SBC engines from the 1950s through the early 2000s. These replacements are designed to hug the damper so it's easier to line up the damper and pointer for more accurate timing. Additional details: * Available for different harmonic balancer diameters * Billet aluminum construction with a black anodized finish * Stainless steel hardware included * Up to 4 degrees of adjustment are possible
( 1 )
$33.71
Engine Works camshaft retainer plates are designed to fit behind the front cover and act as a seal for the front oil passages that feed oil to the lifters, cam, and main bearings. These steel plates support greater cam loads and feature a specially designed silicone O-ring seal to ensure proper sealing.
Not Yet Reviewed
$21.86
Engine Works offers timing covers in a variety of styles for many Chevy and Ford engine applications. The one- or two-piece covers are available in stamped steel or diecast aluminum—in multiple finishes. These replacements are essential in protecting the timing belt, timing chain, or cam belt of your vehicle from road debris, grime, and gravel. Order the model recommended for your ride.
Not Yet Reviewed
$23.71
Engine Works rocker arms studs give you more consistent rocker geometry to keep the rockers, pushrod, and valve stems in alignment. Each stud is machined from 8740 alloy tool steel, roll-threaded, heat-treated and finished with a black oxide, corrosion-resistant finish. Studs are available in a variety of lengths and thread sizes. Sold in sets of 16. Singles are also available. Order the studs recommended for your vehicle and engine application.
Not Yet Reviewed
$31.24
—
$43.71
Engine Works offers camshaft locking plates to keep your cam and timing gear locked securely together. These economical locking accessories give you extra insurance and peace of mind when installing a performance camshaft. Each plate is stamped from cold steel, features bendable tabs to lock the cam bolts in place and is finished in black oxide. Kit comes with zinc alloy 150,000 psi bolts to lock the cam plate into place after they're torqued to spec. Order the cam locking plate recommended for your make/model.
Not Yet Reviewed
$28.71
Engine Works offers valve cover gaskets for a wide range of applications—including many Chevrolet and Ford small block and big block engines from 1955 and up. They're available in a variety of materials, thicknesses, and quantities. These replacement gaskets are placed between the engine and valve cover to tightly seal the oil inside the engine body. A worn-out gasket can allow oil to leak into other parts of the engine, causing performance issues. Order the pair or set of 20 designed to fit your vehicle.
Not Yet Reviewed
$21.21
—
$46.21
Engine Works offers rear main seals for a wide range of applications, including many Chevrolet, Ford, GM, and Mopar vehicles from the 1950s and up. The one- or two-piece gaskets are made from fluoroelastomer rubber or silicone for long-lasting, leak-free performance. Order the seal recommended for your ride.
Not Yet Reviewed
$21.21
—
$28.71
Engine Works offers several options of intake manifold bolts to purchase exactly what you need for small block or big block engine. The bolts are available in different sizes and finishes, with or without washers, and in different quantities. Choose the 12-point intake bolts in the size, quantity, and finish you need.
Not Yet Reviewed
$21.86
—
$29.36
Engine Works offers intake manifold gasket sets for a variety of applications, including many Ford small block V8s from the early 1960 and up. Constructed from premium fiber material blended with multiple elastomer layers, these replacement gaskets deliver a snug, fluid-resistant seal. Engine Works is synonymous with top-tier automotive solutions, catering to the needs of racers and engine builders alike. Order the gaskets designed to fit your vehicle.
Not Yet Reviewed
$21.21
—
$23.71
Engine Works Sportsman Series timing sets are available in single- or double-roller options for Chevy, Ford, and Chrysler big block and small block engines. Order the replacement set recommended for your application. Details below: * Double roller models: -- .200 in. diameter double roller chain -- Cast iron cam sprocket -- 3-keyway crank sprocket with +/- 4 in. cam adjustment * Single roller models: -- Very large .334 in. diameter seamless single roller chain -- Cast iron cam sprocket -- 3-keyway crank sprocket with a +/- cam adjustment -- Heat-treated crank sprocket with black oxide coating
( 1 )
$37.46
—
$49.96
Engine Works offers distributor gears for a variety of applications, including many stock or Ready-to-Run (RTR) distributors. These replacements are precision-engineered and meticulously machined from extruded bonze for unparalleled durability. They're available in multiple shaft diameters to fit OEM-style and aftermarket distributors. On vehicles with mechanical spark timing, the distributor gear sits at the bottom of the distributor shaft, where it meshes with the gear on the camshaft. This gear can wear out over time, or you might need one that's compatible with a new camshaft. To maintain proper timing, order the replacement recommended for your vehicle.
Not Yet Reviewed
$20.56
—
$47.49
Engine Works offers guideplates for a wide range of applications, including many Chevy and Ford engine applications from the 1950s and up. These replacements are pressed from heat-treated steel and finished in a black oxide coating. They're available in flat or raised style, in 5/16 or 3/8 in. diameter.
Not Yet Reviewed
$20.31
Engine Works hydraulic roller lifter guides are the newer design LS2 trays used in all current LS builds (except for the active cylinder management engines). These plastic guides feature increased support in the design. They're available in a set of 4.
Not Yet Reviewed
$48.71
Engine Works offers locking dipsticks for Powerglide, THM350, and THM400 transmission. These dipsticks feature a bellhousing mounted steel tube, which installs into the transmission case for accurate fluid readings, and are available in standard or extended lengths. With a legacy of delivering quality, affordable parts in the performance and racing industries, Engine Works provides the tools you need to succeed.
Not Yet Reviewed
$37.46
Engine Works offers a comprehensive portfolio of high-quality, high-value, and high performance products for racers, engine builders, and everyday gearheads. These oil pan gaskets are designed for a variety of Chevrolet small block LS-based engine applications from 1997 and up. The one-piece replacement gaskets are made from cellulose/nitrile rubber to ensure a secure, leak-free seal. They're designed to factory specs for proper fit and long-lasting performance.
Not Yet Reviewed
$32.46
—
$44.96
The right tool for that special job--Engine Works oil pump primers include bushing for proper pressurization of the oiling system. They work with a 3/8 in. chuck drill to properly lubricate your engine's oil pump and passages before start-up.
Not Yet Reviewed
$26.21
Some fasteners have a specific purpose, providing the best fit and performance for that purpose. Engine Works oil pans stud kits will mate with the specified oil pan applications for a secure, leak-free fit. The Grade 8 studs feature a black oxide finish and a bullet point for easier pan installation. The kits include lock nuts. Select the kit with the right quantity for your engine.
Not Yet Reviewed
$43.71
Engine Works cylinder head dowel pins ensure alignment between the cylinder head and block. These small cylindrical components are available in different quantities for small block, big block, and LS engines. Select the ones needed for your engine assembly.
Not Yet Reviewed
$21.21
—
$22.44
Engine Works rod bearing sets are quality bearing sets available in various series and clearances. Offered in bi-metal or Alecular tri-metal construction, these rod bearing sets also come in a variety of clearance options from standard through .030 in., with a .001 in. X-clearance available on some sets. When you want high-quality and high-value parts for your performance vehicle, Engine Works delivers. Check availability and order the set recommended for your ride.
Not Yet Reviewed
$21.21
Engine Works solid steel motor mounts replace stock OEM-style rubber mounts with added strength and rigidity to stop torque loss and binding linkages—a common result of excessive engine movement. They also eliminate the need for bulky torque straps and chains. Engine Works steel engine mounts are available in different sizes and finishes. Select the pair preferred for your engine.
Not Yet Reviewed
$37.46
Engine Works lifter valley vents help control oil flow to cam and lifters and holds down camshaft oil windage. Crafted from T-6 aluminum, they are 2 1/4 in. long. Note: Factory vent holts must be tapped to 1/4 in.
Not Yet Reviewed
$37.46
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
