Availability
Have you ever had a tune-up on your engine that was just perfect? Or, did you spend the time and money to dyno your engine? Wouldn't it be nice to go to the track and get back to that same tune-up every single time? With the Computech EGT Plus (exhaust gas temperature) monitor kits you can make sure that your vehicle is tuned correctly, week in and week out. Choose the EGT Plus monitor kit that suits your needs and get ready to tune your fuel system with confidence to maintain the performance edge and consistency you need to be a winner! Additional features of the EGT Plus monitor kits include: * Available with single or dual probes * Available in weld-in or clamp-on styles * Unit monitors dual temperature channels * Power source through 9 V battery or 12 V vehicle supply * Continuous mode--simple maximums * Record switch mode -- Choose when to record -- Maximum temperature and rpm * Trans-brake mode -- Launch temperature and rpm -- Finish line temperature and rpm -- Maximum temperature and rpm -- Time maximums occurred -- Notable time, temperature, and rpm
( 2 )
$479.95
—
$629.95
Computech weld-in header adapters allow you to connect a professional EGT probe to any of your cylinders. Simply drill a hole, weld them in place, and you're ready to add your exhaust sensor. They utilize a 1/8 in. pipe thread and are made to fit with the 3/16 in. diameter probes, as are standard for Computech.
Not Yet Reviewed
$4.95
Computech clamp-on temperature sensors are designed for use with Computech's EGT Plus Series, as well as DataMaxx data logger systems. The probe is a 3/16 in. diameter and utilizes a clamp that expands to 2 1/2 in. The probe lead has a male K-type connector on the end and can easily be shortened to your installation. The Computech clamp-on temperature sensors are designed to be used with regular-octane gasoline, high-octane racing gas, ethanol, methanol, and nitro mixtures. They cannot be used with diesel, as a specific diesel exhaust gas sensor is required.
Not Yet Reviewed
$139.95
Computech weld-in temperature sensors are designed for use with Computech's EGT Plus Series, as well as DataMaxx data logger systems. The probe is a 3/16 in. diameter and utilizes an 1/8 in. pipe thread weld-in bung. The probe is centered in the tube using a compression fitting screwed into the weld-in bung, both of which are included. The probe lead has a male K-type connector on the end and can easily be shortened to your installation. The Computech weld-in temperature sensors are designed to be used with regular octane gasoline, high-octane racing gas, ethanol, methanol, and nitro mixtures. They cannot be used with diesel, as a specific diesel exhaust gas sensor is required.
Not Yet Reviewed
$109.95
Computech male K-type connectors will allow you to replace the end of any weld-in EGT probe. When installing the connectors, be sure to run the red wire to the negative terminal and the yellow wire to the positive terminal.
( 1 )
$11.95
Computech female K-type connectors will allow you to extend any standard EGT probe or liquid temperature probe when combined with the thermocouple wire. When installing the connectors be sure to run the red wire to the negative terminal and the yellow wire to the positive terminal.
Not Yet Reviewed
$11.95
Maintain sealed tight connections with these Computech compression fittings. They are made of quality materials and are available in different configurations, so you can choose what's best for your system.
Not Yet Reviewed
$8.95
Computech shock travel sensors are designed for monitoring suspension travel. They are available in 4 in. or 8 in. lengths and are one of the strongest shock travel sensors on the market. Mounting is a breeze, and the information gathered through shock travel can go a long way to perfecting your setup.
Not Yet Reviewed
$399.95
Computech bolt-on temperature sensors are designed for use with Computech's EGT Plus Series, as well as DataMaxx data logger systems. The probe is a 3/16 in. diameter and utilizes a 3/8 in. diameter ring connector for a bolt-on installation. The Computech bolt-on temperature sensors are designed to be used with regular octane gasoline, high-octane racing gas, ethanol, methanol, and nitro mixtures.
Not Yet Reviewed
$159.95
—
$169.95
Computech liquid temperature monitor kits are designed to get you the readings you need. The probe is centered in the tube using a compression fitting screwed into the weld-in bung, both of which are included in the kits.
Not Yet Reviewed
$129.95
—
$159.95
If you have a damaged or missing thermocouple, you'll need one of these Computech liquid temperature replacement thermocouples. They include a compression fitting for installation.
Not Yet Reviewed
$79.95
Computech vacuum pressure monitor kits allow you to measure pressures from -14.7 to +30 in. of mercury. With calibration values available for inches of mercury (inHg) or pounds per square inch (psi), they work great for low-range pressures that have a tendency to go into a vacuum state, such as boost pressure. Computech vacuum pressure monitor kits include a stainless steel pressure transducer and a 15 ft. extension cable. They are compatible with most gases and fluids, including gasoline, methanol, and oil.
Not Yet Reviewed
$359.95
Computech 15 psi pressure monitor kits are extremely accurate low-range pressure sensors, perfect for monitoring carbureted fuel pressure and boost psi. The pressure sensor will monitor from 0 to 15 psi. The kits include a stainless steel pressure transducer and 15 ft. extension cable. They are compatible with most gases and fluids, including gasoline, methanol, and oil.
Not Yet Reviewed
$299.95
Computech 100 psi pressure monitor kits are extremely accurate and will be sure to capture every little pressure change. Measuring accurately throughout the entire zero to 100 psi range, they work great for oil, boost, or fuel psi. The kits include a stainless steel pressure transducer and 15 ft. extension cable. They are compatible with most gases and fluids, including gasoline, methanol, and oil.
Not Yet Reviewed
$299.95
Computech 500 psi pressure monitor kits have a great wide-range pressure sensor that is still extremely accurate in low and high-pressure environments. They are typically used for oil pressure, injected fuel psi, and transmission pressure. The pressure sensor will monitor from 0 to 500 psi. Computech 500 psi pressure monitor kits include a stainless steel pressure transducer and 15 ft. extension cable. They are compatible with most gases and fluids, including gasoline, methanol, and oil.
Not Yet Reviewed
$299.95
Computech 1,500 psi pressure monitor kits are great for monitoring nitrous bottle pressure, as well as brake pressure. The pressure sensor will monitor from 0 to 1,500 psi. The kits include a stainless steel pressure transducer and 15 ft. extension cable and are compatible with most gases and fluids, including gasoline, methanol, and oil.
Not Yet Reviewed
$299.95
Computech exhaust temperature kits are one of the most economical ways of maintaining a consistent tuneup, week in and week out. The leaner your engine is, the hotter the temperature. The richer the engine is, the cooler the temperature is. Where EGT sensors really excel is maintaining a specific tuneup. Once you find a setup where your engine is running safely and consistently, you can note the temperature and then strive for that temperature every race, ensuring your engine is tuned consistently. The kits include a 3/16 in. stainless steel exposed junction thermocouple, a compression fitting, a 10 ft. braided stainless extension wire, and a connector.
Not Yet Reviewed
$109.95
Computech custom 8-cylinder thermocouple kits come with your choice of either weld-in or clamp-on EGT probes. The EGT probes are 3/16 in. and can stand up to the most extreme temperatures. Your custom 8-cylinder thermocouple kits are available in either the Chevy (1, 3, 5, 7) and (2, 4, 6, 8) configuration or Ford (1, 2, 3, 4) and (5, 6, 7, 8) configuration. Each EGT probe has a custom-length lead, allowing the probes to plug in cleanly to the EGT modules. These Computech custom 8-cylinder thermocouple kits allow for the removal of the headers without having to take out the thermocouple sensors or un-wire.
Not Yet Reviewed
$1,599.95
Computech throttle position kits are designed to monitor what happens to the car down the track. Did you let off the throttle before or after the finish line? How much did you let off? How much mph did that kill? With these kits, you can finally monitor exactly what the driver did at the top end and increase your chances of reproducing successful results.
Not Yet Reviewed
$299.95
Computech DataMaxx main modules are the heart and brain of our entire data acquisition system. You cannot use any Computech data logger components, including the LCD, unless you have the main module. The main modules themselves have room for four rpm sensors, four analog sensors (temperature, pressure, etc.), two switch event monitors, two light outputs, and battery voltage. Keep in mind that the main modules are simply the base of the system and are completely expandable by purchasing an expansion analog module or EGT module.
Not Yet Reviewed
$999.95
For years, data loggers have been expensive and complicated for the weekend racer. Good news, Computech has changed that with the cutting-edge technology of DataMaxx bracket kit data loggers, along with user-friendly software, and 24/7 weekend tech support. Datamaxx supplies the essential information need, plus a beautiful dash. You don't pay for anything you're not going to use with this kit; and you have the option to upgrade any time. Computech DataMaxx bracket kit data logger features: * DataMaxx main module * Billet aluminum enclosure * 100 samples per second per channel * Multiple CAN bus connections * Multiple rpm channels, magneto-compatible * Switch input channels * Warning light outputs * Multiple analog channels * Battery voltage channel * Sensors: engine rpm, driveshaft rpm, fuel psi, oil psi, water temp, and single EGT probe Computech DataMaxx LCD dash function features: * 10 channels per screen * Unlimited screen configurations * Customizable shift and warning lights * SD memory card port * Variable speed playback (1/10x, 1/4x, 1/2x, 1x, 2x, 4x, 10x, 100x) * Single cable connection * Day/night brightness modes * Eliminates need for conventional gauges
( 1 )
$2,349.95
Computech DataMaxx Remote SD Modules are designed specifically for vehicles that are using magneto's. Magneto's disperse a wide range of electromagnetic noise and are necessary to get the SD circuit physically far away from that radius of noise corruption. The remote SD modules come with a 15 ft. cable and can also be used as a convenient way to mount them in an easy to reach location.
Not Yet Reviewed
$379.95
These Computech replacement magnets are designed for use in driveshaft, input shaft, and universal shaft rpm sensors.
Not Yet Reviewed
$3.95
Computech DataMaxx EGT modules are designed to allow you to add up to four additional temperature sensors for exhaust gas temperature, cylinder head temperature, oil temperature, or water temperature to your DataMaxx main module. Their CAN-bus wiring only requires a single 4-conductor cable to connect the EGT module to the main module, simplifying installation.
Not Yet Reviewed
$349.95
Modal Header
Truck / SUV
Jeep®
Restoration
Stock Replacement
Late Model Muscle
Tools
Gifts, Clothing, & More
Circle Track
Street Rod
Powersports
Paint & Body
Marine
Jr Dragster
