Summit Racing® M2008 Series Carburetors SUM-M08600VS

yes it will i put my on a ford 302 fit was perfect and it runs great

RICK from NC answered on June 19, 2017

Yes it will fit. I have an Edelbrock on my 351w and as far as carbs they are interchangeable among the V8's. The carb has two mounting configurations built in so if you have the wide base it already has mounting holes set up for that so there should be no problem about the carbs fitting. All the cars that I have are older Fords so I've had to deal with a lot of carbs and I can tell you with certainty that this Summit carburetor will fit on your 289 intake especially if it's Edelbrock.

GEORGE from GA answered on June 15, 2017

I really do not know it is suppose to be very similar to the Holley 1860 i would think the bolt pattern is the same i love my carb ! but do a google search mine went on a ford 5.0 but i used summits manifold the whole kit was 500 hundred bucks but buy different manifold studs for it theirs are junk. hope that helps !

ALVIN from OH answered on June 23, 2017

Yes

ROBERT from SC answered on June 21, 2017

Yes it well you got to ask them for one for the Ford but I'm pretty sure they all of them fit both cars Chevy and Ford

WALTER from OH answered on June 19, 2017

YES

JOHN A from OR answered on June 16, 2017

This carb seems to be universal duty. If tech people says will work..it will work. took off holley 4150 from edelbrock manifold and the summit carb works perfecto. Really am impressed.
Good luck, J

DORIS J from OH answered on June 14, 2017

I used it to replace a Holley 650cfm

DAVID from GA answered on June 17, 2017

It should from what I have read. I just got my set up and as you know the SB Chevy is so widely used. Good luck I hope does what you need.
P.S. The Summit people were very helpful with my application.

WILLIAM from OH answered on June 15, 2017

Yes

MARK E from IN answered on June 14, 2017

Yes. The Summit Carb has the same throttle plate style as the Holley Carbs. (Square Bore)

BRAD from KS answered on June 21, 2017

Yes it will with no problems

AARON from CA answered on June 15, 2017

It should bolt right on. It's comparable to an autolite 4100.

FRANK from NM answered on June 24, 2017

yes I think it will fit

RICHARD from SC answered on June 19, 2017

Yes, it will and you will love it I'm sure, I sure love mine.
I bought the combo so lm using Summits intake as well, but it will bolt right on an Edelbrock square bore intake

RICK from OK answered on June 14, 2017

I use it to replace my Holley 650cfm Direct fit with no adjustments. On a strocker motor.

DAVID from GA answered on June 17, 2017

Yes

MICHAEL from CA answered on June 24, 2017

You didn't mention which model edelbrock manifold if it is a square bore intake manifold it should work I put my carb. On a edelbrock rpm air gap manifold

JOHN E from CA answered on June 14, 2017

My limited knowledge it's a standard square bore that would fit. I haven't fine tuned mine yet but bolted it on and run it like I stole it! Beats the old E brand that came with my ride

RICHARD from OH answered on June 20, 2017

YES PLACE ON BACK OF CARB FOR BRAKE BOOSTER ON FRONT FOR PCV

GEORGE from TX answered on October 31, 2017

There is only one large vacuum port off the rear base of this carb, you may be able to tap off the manifold or air cleaner for your PCV.

MICHAEL from OH answered on October 26, 2017

Yes there is

MARK from LA answered on October 13, 2017

Yes

JOHN A from WA answered on October 18, 2017

Pcv on front of carb. The brake port plumbs into manifold

ROBERT from MI answered on October 16, 2017

There is a port in the rear, favored to the drivers side. I had to use the intake port for the brake booster

JEFFREY from KY answered on October 18, 2017

yes, check intake for brake port

RICHARD from SC answered on November 03, 2017

Yes, i am using both on mine

MIKE from NC answered on October 30, 2017

yes to both ports

TOM from IL answered on October 25, 2017

Yes, on the back drivers side.

LOUIS from LA answered on November 03, 2017

Yes, there is provision for pcv, timing advance, and brake booster

STEVEN from NV answered on October 21, 2017

Yes.

ERNEST from OK answered on November 03, 2017

yes it at the front

FRANK from AZ answered on November 04, 2017

yes has ports for trans vacuum and distributor vacuum and brake-pvc just like a holley

JEFFERY D from OH answered on October 29, 2017

Check your Converter+

DERRICK from TN answered on August 13, 2017

I believe we may over carb alot of motors,if yours ran well with a 600 i would swap summits 600 for the 750. I just put a summit 600 cfm on a ford 302(new rebuild w/mild cam). It replaced a edelbrock 750(new) ,that was extremely rich 2 the point of washing down the cylinders into the oil.With the new summit I only adjusted idle speed.It starts better,idles good runs cleaner.Please note however this engine is a engine test frame only and car has not been actually driven.I hope this helps,sincerely John C.,satisfied Summit customer.

JOHN L from ID answered on August 24, 2017

Used a 600 on '66 428 Galaxy for a couple of years and it was fine. Run the numbers and you will probably find that it denotes a 625-650 for street use. With auto trans you need controlled secondaries (air valve/vacuum). Mech secondaries will oftentimes provide too much air on opening. Currently have 600 on 413 with automatic. Again is for street use. Racing would be 700-750 for high rpm launches. Hope this helps.

ROBERT from TX answered on August 23, 2017

Should be a good match

REGINALD from MI answered on August 16, 2017

I think that in this case the 780 should perform good with this English you may have a issue with carb.

DOUGLAS from GA answered on August 18, 2017

A 600 should be large enough for this application. You could try decreasing your fuel jets before removing and purchasing a new carb.

ERIC from MO answered on August 18, 2017

The 750 cfm should be alright since this engine is a 429 with a more than stock camshaft. I would check to see if there's a problem with the accelerator pump circuit. I think that there's a lack of fuel from the accelerator pump either from the way that the pump is adjusted or in the, screw in, primary nozzle restriction,(squirter) size. I'd revert back to the original size, if its been changed, and go from there. Make sure that the pump arm is riding on the nylon cam like it should and that it has the recommended color pump cam installed. Usually its the green one. The accelerator pump must be adjusted with the throttle completely open, with a clearance of .010"-.015" between the pump lever and the face of the adjustment screw head.

CHARLES from FL answered on July 19, 2018

I am running a summit 650 cfm on my HO 302 and it runs great... i would say the 750 is probably more than you need...

DAVID from PA answered on August 24, 2017

sounds like it is running out of gas when you step on it, float to low

KEVIN from NE answered on August 25, 2017

I think yes.
Runs perfect on my Dodge. 318 mid size cam

More pier than edelbrock 750 previous.

BRIAN from IL answered on August 25, 2017

CHECK YOUR SPARK PLUGS TO SEE.

RICHARD from SC answered on August 23, 2017

I put this carb on my stock 330ci olds about a week ago. Set the air jets, adjusted the floats, hooked up the electric choke and it worked fine.

STEPHEN from CA answered on September 27, 2017

Will work just fine. Just don't try to get too radical with the cam. as far as cubic inches; I have used this on a 428 street engine with torker cam and currently on a 413 with mild cam.

ROBERT from TX answered on September 22, 2017

I put on my 350 an works great no adjustment needed definitely recommend it

TIMOTHY from GA answered on September 26, 2017

In my experience it's hard to beat the simplicity of bolting it on and driving! Size should be fine. I want to fine tune mine but drivability is good as is.

RICHARD from OH answered on September 19, 2017

It should work great with little to no adjustments. Great carb for the price.

DAVID from GA answered on September 22, 2017

Yes it will.

CARLTON L from NC answered on September 21, 2017

It will be an excellent choice. I have one on my 429 ford and it is perfect.

TOM from IL answered on September 20, 2017

I have this on my 350, with a cam and it highrise intake, worked great out the box. Bolt on fun, and worth the money

TAYLOR from GA answered on September 28, 2017

It sure will. I have a rebuilt 350, edelbrock preformer intake, with a mild cam and it works amazing. Smooth and clean starts and really gets the gas to the motor. Originally I had a 600 cfm Edelbrock carb and this thing trumps it 10fold. Love this carb and I will never buy any other brand for my future projects. It will work great.

ANDRE from MA answered on September 20, 2017